IMPORTANT SAFETY INSTRUCTIONS
aWARNINGa
FOLLOW THESE BASIC PRECAUTIONS TO
REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY WHEN USING YOUR ICE
MAKER.
•
•
READ ALL INSTRUCTIONS BEFORE USING THE ICE MAKER.
DANGER: RISK OF CHILD ENTRAPMENT.
CHILD ENTRAPMENT AND SUFFOCATION ARE NOT PROBLEMS OF THE PAST. JUNKED
OR ABANDONED APPLIANCES ARE STILL DANGEROUS.
BEFORE YOU THROW AWAY YOUR ICE MAKER: TAKE OFF THE DOOR.
NEVER ALLOW CHILDREN TO OPERATE, PLAY WITH, OR CRAWL INSIDE THE
APPLIANCE.
•
•
•
•
NEVER CLEAN ICE MAKER PARTS WITH FLAMMABLE FLUIDS. THE FUMES CAN
CREATE A FIRE HAZARD OR EXPLOSION.
DO NOT STORE OR USE GASOLINE OR ANY OTHER FLAMMABLE VAPORS AND LIQUIDS
IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. THE FUMES CAN CREATE A FIRE
HAZARD OR EXPLOSION.
INSTALLATION INSTRUCTIONS
BEFORE USING YOUR ICE MAKER
REMOVE THE EXTERIOR AND INTERIOR PACKING.
CHECK TO BE SURE YOU HAVE ALL OF THE FOLLOWING PARTS:
¾
•
•
•
•
•
•
1 ICE BUCKET
1 PLASTIC SCOOP
1 HOSE, 25 FT.
1 INSTRUCTION MANUAL
•
•
BEFORE CONNECTING THE ICE MAKER TO THE POWER SOURCE, LET IT STAND UPRIGHT
FOR APPROXIMATELY 2 HOURS. THIS WILL REDUCE THE POSSIBILITY OF A MALFUNCTION
IN THE COOLING SYSTEM FROM HANDLING DURING TRANSPORTATION.
CLEAN THE INTERIOR SURFACE WITH LUKEWARM WATER USING A SOFT CLOTH.
¾
INSTALLATION OF YOUR ICE MAKER
•
THIS APPLIANCE IS DESIGNED TO VENT HOT AIR THROUGH THE FRONT VENT. THIS
ALLOWS FOR INSTALLATION IN A RECESSED OR BUILT-IN APPLICATION, IF DESIRED.
PLACE YOUR ICE MAKER ON A LEVEL SURFACE THAT IS STRONG ENOUGH TO SUPPORT
THE ICE MAKER WHEN IT IS FULLY LOADED. REMEMBER THAT THE UNIT WILL BE
SIGNIFICANTLY HEAVIER ONCE IT IS OPERATIONAL AND FULLY LOADED. LEVEL YOUR ICE
MAKER BY ADJUSTING THE LEGS AT THE FRONT OF THE ICE MAKER.
LOCATE THE ICE MAKER AWAY FROM DIRECT SUNLIGHT AND SOURCES OF HEAT (STOVE,
HEATER, RADIATOR, ETC.). DIRECT SUNLIGHT MAY AFFECT THE FINISH AND HEAT
SOURCES MAY INCREASE ELECTRICAL CONSUMPTION. EXTREME COLD AMBIENT
TEMPERATURES MAY ALSO CAUSE THE ICE MAKER MALFUNCTION. THIS ICE MAKER IS
DESIGNED FOR INSTALLATION INDOORS IN “ROOM TEMPERATURE” AMBIENT
CONDITIONS.
•
•
•
•
AVOID LOCATING THE ICE MAKER IN MOIST/HUMID AREAS. TOO MUCH MOISTURE IN THE
AIR WILL CAUSE FROST TO FORM QUICKLY ON THE EVAPORATOR REQUIRING FREQUENT
DEFROSTING.
PLUG THE ICE MAKER INTO AN EXCLUSIVE PROPERLY INSTALLED GROUNDED WALL
OUTLET. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER CORD. ANY QUESTIONS CONCERNING POWER AND/OR
GROUNDING SHOULD BE DIRECTED TOWARD A CERTIFIED ELECTRICIAN.
1
¾
ELECTRICAL CONNECTION
aWARNINGa
IMPROPER USE OF THE GROUNDED PLUG CAN RESULT IN THE RISK OF ELECTRICAL
SHOCK. IF THE POWER CORD IS DAMAGED, HAVE IT REPLACED BY AN AUTHORIZED
SERVICER.
•
•
THIS ICE MAKER SHOULD BE PROPERLY GROUNDED FOR YOUR SAFETY. THE POWER
CORD OF THIS ICE MAKER IS EQUIPPED WITH A THREE-PRONG PLUG WHICH MATES WITH
STANDARD THREE PRONG WALL OUTLETS TO MINIMIZE THE POSSIBILITY OF ELECTRICAL
SHOCK.
DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG
FROM THE POWER CORD SUPPLIED.
•
•
•
DO NOT USE AN EXTENSION CORD TO CONNECT POWER TO THE UNIT.
DO NOT USE A TWO-PRONG GROUNDING ADAPTER.
IF YOU ONLY HAVE A TWO-PRONG WALL RECEPTACLE, CONTACT A QUALIFIED
ELECTRICIAN TO HAVE IT REPLACED WITH A 3-PRONG RECEPTACLE IN ACCORDANCE
WITH APPLICABLE ELECTRICAL CODES.
•
•
THIS ICE MAKER REQUIRES A STANDARD 115 VOLTS A.C. 60HZ ELECTRICAL OUTLET WITH
THREE-PRONG GROUND.
THE CORD SHOULD BE SECURED BEHIND THE ICE MAKER AND NOT LEFT EXPOSED OR
LOOSE.
¾
EXTENSION CORD
BECAUSE OF POTENTIAL SAFETY HAZARDS, THIS APPLIANCE IS NOT RECOMMENDED FOR
USE WITH AN EXTENSION CORD. HOWEVER, IF YOU MUST USE AN EXTENSION CORD, USE
ONLY A UL/CUL-LISTED, 3-WIRE GROUNDING TYPE APPLIANCE EXTENSION CORD WITH A
GROUNDING TYPE PLUG AND OUTLET. THE ELECTRICAL RATING OF THE CORD MUST BE 115
VOLTS AND AT LEAST 10 AMPS.
¾
CONNECTING THE WATER SUPPLY
aWARNINGa
IMPROPER WATER LINE CONNECTION MAY RESULT IN FLOODING
YOU MUST USE A LICENSED PLUMBER
REVIEW STATE AND LOCAL PLUMBING CODES BEFORE INSTALLATION
•
•
ALL THE NECESSARY HARDWARE IS NOT PROVIDED (AS THE PLUMBING FIXTURES AT
THE INSTALLATION POINT MAY DIFFER) FOR INSTALLATION SO IT IS NECESSARY TO HIRE
A PROFESSIONAL LICENSED PLUMBER TO COMPLETE THE INSTALLATION.
CONNECT TUBING (SUPPLIED WITH UNIT) TO THE NEAREST COLD WATER SOURCE.
CONNECT SUFFICIENT TUBING TO THE UNIT TO ALLOW THE
APPLIANCE TO BE MOVED FREELY FOR CLEANING AND SERVICE.
ALSO MAKE SURE THAT THE TUBING IS NOT PINCHED OR DAMAGED
DURING TRANSPORTATION/INSTALLATION.
•
•
POSITION UNIT TO ALLOW FREE AIRFLOW THROUGH THE FRONT
GRILL (SEE FIGURE 1).
WIPE OUT INSIDE OF UNIT AND ICE BUCKET WITH A DAMP CLOTH.
FIGURE 1
2
¾
REVERSING THE DOOR SWING OF YOUR ICE MAKER
THIS APPLIANCE HAS THE CAPABILITY OF THE DOOR OPENING FROM EITHER THE LEFT OR
RIGHT SIDE. THE UNIT IS DELIVERED TO YOU WITH THE DOOR OPENING FROM THE LEFT
SIDE (HINGED ON THE RIGHT). TO REVERSE THE OPENING DIRECTION, PLEASE CALL
CUSTOMER SERVICE FOR DIRECTIONS.
OPERATING YOUR ICE MAKER
¾
INITIAL START-UP OPERATION
1. MAKE SURE THE UNIT IS PROPERLY INSTALLED BY A LICENCED PLUMBER.
2. MAKE SURE THE ON-OFF SWITCH IS IN THE “OFF” POSITION.
3. PLUG THE APPLIANCE INTO AN 115V POLARIZED AND GROUNDED WALL ELECTRICAL
OUTLET.
4. PLACE THE ON-OFF SWITCH IN THE “ON” POSITION.
5. MAKE SURE THE WATER SUPPLY IS ON. AS SOON AS THE INNER MECHANISM REACHES
THE PROPER TEMPERATURE, THE ICEMAKER COMPONENT WILL FILL THE MOLD WITH
WATER.
6. THE FIRST CUBES MAY BE SMALL BECAUSE OF AIR IN THE WATER LINE. LATER CUBES
WILL BE OF STANDARD CRESCENT MOON TYPE SIZE AND SHAPE.
7. THE APPROXIMATE TIME FOR THE FIRST CYCLE IS BETWEEN 30-40 MINUTES.
8. EACH CYCLE WILL TAKE ABOUT 5 OUNCES OF WATER SO YOU SHOULD HAVE A FULL
TRAY AFTER ABOUT 11 HOURS.
IMPORTANT: THROW AWAY ALL ICE CUBES MADE DURING THE FIRST 3 HOURS OF
OPERATION.
•
WHEN THE ICE BUCKET IS FULL, THE ICE MAKING MECHANISM WILL
AUTOMATICALLY SHUT OFF. THE REFRIGERATION SYSTEM WILL
CONTINUE TO COOL AND MAINTAIN FREEZING TEMPERATURES WITHIN
THE UNIT.
•
•
•
THE ICE MAKING FUNCTION MAY BE TEMPORARILY STOPPED BY
RAISING THE METAL ARM INTO AN UPRIGHT POSITION (SEE FIGURE 2)
IF THE ICEMAKER IS NOT USED REGULARLY, WE RECOMMEND THAT THE
ICE BUCKET BE EMPTIED PERIODICALLY TO ENSURE FRESH ICE.
SOMETIMES THE CUBES MAY APPEAR CLOUDY. THIS SHOULD NOT BE A CAUSE FOR
CONCERN AND HAS NOTHING TO DO WITH THE TASTE OR CHEMICAL MAKE-UP OF THE
WATER.
FIGURE 2
•
•
THE FRONT GRILL SHOULD BE KEPT FREE OF DUST AND LINT TO PERMIT FREE AIRFLOW.
THIS UNIT SHOULD BE DEFROSTED ABOUT EVERY 4-6 WEEKS OR WHEN FROST ON THE
ICE MAKER WALLS IS EXCESSIVE (¼” THICK OR THICKER). TO DEFROST, TURN THE UNIT
OFF, REMOVE/DISCARD THE EXISTING CUBES AND KEEP DOOR OPEN AT LEAST TWO
INCHES. YOU MAY WANT TO PUT A TOWEL DOWN TO SOAK UP ANY WATER DRAINAGE
CAUSED BY DEFROSTING THE UNIT.
•
DO NOT SCRAPE OFF THE FROST WITH ANYTHING EXCEPT A PLASTIC SCRAPER.
CARE AND MAINTENANCE
¾
CLEANING YOUR ICE MAKER
•
TURN THE SWITCH CONTROL TO "OFF", UNPLUG THE ICE MAKER AND REMOVE THE
BUCKET.
•
WASH THE INSIDE WITH A WARM WATER AND BAKING SODA SOLUTION. THE SOLUTION
SHOULD BE ABOUT 2 TABLESPOONS OF BAKING SODA TO A QUART OF WATER.
WASH THE BUCKET WITH A MILD DETERGENT SOLUTION.
THE OUTSIDE OF THE ICE MAKER SHOULD BE CLEANED WITH MILD DETERGENT AND
WARM WATER.
•
•
3
•
•
THE STAINLESS STEEL COMPONENTS OF THE DOOR SHOULD BE CLEANED WITH
STAINLESS STEEL CLEANER
THE CONDENSER COILS SHOULD BE VACUUMED WHEN THEY ARE DUSTY OR DIRTY.
CAUTION
FAILURE TO UNPLUG THE ICE MAKER WHEN CLEANING, MOVING, OR SERVICING IT COULD
RESULT IN ELECTRICAL SHOCK OR PERSONAL INJURY.
¾
POWER FAILURE
MOST POWER FAILURES ARE CORRECTED WITHIN A FEW HOURS AND SHOULD NOT AFFECT
THE TEMPERATURE OF YOUR ICE MAKER IF YOU MINIMIZE THE NUMBER OF TIMES THE DOOR
IS OPENED. IF THE POWER IS GOING TO BE OFF FOR A LONGER PERIOD OF TIME, YOU
SHOULD TAKE THE PROPER STEPS TO DISCONNECT YOUR APPLIANCE.
¾
1.
2.
3.
VACATION TIME/STORAGE
SHUT OFF THE WATER SUPPLY AT THE MAIN WATER VALVE.
DISCONNECT THE WATER SUPPLY LINE FROM THE VALVE.
ALLOW THE UNIT TO RUN FOR AN HOUR OR TWO UNTIL ALL REMAINING ICE CUBES HAVE
BEEN EJECTED AND ALL WATER HAS CYCLED THROUGH THE SYSTEM AND HAS BEEN
MADE INTO ICE CUBES.
4.
5.
6.
DISCONNECT THE UNIT FROM THE MAIN POWER SOURCE.
DRY OUT EXCESS WATER FROM THE ICE MAKER ASSEMBLY
LEAVE THE DOOR OPEN AT LEAST TWO INCHES.
¾
•
•
MOVING YOUR ICE MAKER
SECURELY TAPE DOWN ALL LOOSE ITEMS INSIDE YOUR ICE MAKER.
TURN THE LEVELING SCREWS UP TO THE BASE (THEIR SHORTEST LENGTH POSSIBLE) TO
AVOID DAMAGE.
•
•
TAPE THE DOOR SHUT.
MAKE SURE THE ICE MAKER STAYS IN THE UPRIGHT POSITION DURING
TRANSPORTATION.
¾
ENERGY SAVING TIPS
•
THE ICE MAKER SHOULD BE LOCATED IN THE COOLEST AREA OF THE ROOM, AWAY FROM
HEAT SOURCES, AND OUT OF THE DIRECT SUNLIGHT.
4
PROBLEMS WITH YOUR ICE MAKER?
YOU CAN SOLVE MANY COMMON ICE MAKER PROBLEMS EASILY, SAVING YOU THE TROUBLE
OF A SERVICE CALL. TRY THE SUGGESTIONS BELOW TO SEE IF YOU CAN SOLVE THE
PROBLEM BEFORE CALLING FOR SERVICE.
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
NOT PLUGGED IN.
THE ICE MAKER DOES NOT OPERATE
THE CIRCUIT BREAKER TRIPPED OR A
BLOWN FUSE.
THE ICE MAKER POWER SWITCH IS SET TO
"OFF".
NO ICE PRODUCED
AIRFLOW FROM THE FRONT GRILL IS
BLOCKED.
THE ICE MAKER ARM IS SET TO THE OFF
POSITION.
THE WATER SUPPLY IS TURNED OFF.
THE WATER LINE IS CRIMPED.
THE ICE MAKER HAS EXCESSIVE FROST
BUILD UP.
THE COMPRESSOR TURNS ON AND OFF
FREQUENTLY
THE ROOM TEMPERATURE IS WARMER THAN
NORMAL.
THE DOOR IS OPENED TOO OFTEN.
THE DOOR IS NOT CLOSED COMPLETELY.
THE DOOR GASKET DOES NOT SEAL
PROPERLY.
THE ICE MAKER DOES NOT HAVE ADEQUATE
VENTILATION (IS THE GRILL OBSTRUCTED OR
ARE THE CONDENSER COILS DIRTY?)
CHECK TO MAKE SURE THAT THE ICE MAKER
IS LEVEL. ADJUST THE LEVELING LEGS IF
NEEDED
EXCESSIVE VIBRATION
THE ICE MAKER SEEMS TO MAKE TOO MUCH
NOISE
A RATTLING NOISE MAY COME FROM THE
FLOW OF THE REFRIGERANT, WHICH IS
NORMAL.
AS EACH CYCLE ENDS, YOU MAY HEAR
GURGLING SOUNDS CAUSED BY THE FLOW
OF REFRIGERANT IN YOUR ICE MAKER.
CONTRACTION AND EXPANSION OF THE
INSIDE WALLS MAY CAUSE SOME POPPING
AND CRACKLING NOISES.
THE ICE MAKER IS NOT LEVEL.
THE DOOR WILL NOT CLOSE PROPERLY
THE ICE CUBES ARE MELTED TOGETHER
THE ICE MAKER IS NOT LEVEL.
THE DOOR HAS BEEN REVERSED AND IS NOT
PROPERLY INSTALLED.
THE GASKET IS DIRTY.
THE ICE BUCKET IS OUT OF POSITION.
ICE MAKER DOOR IS OPENED TOO OFTEN.
5
LIMITED WARRANTY
This EdgeStar product is warranted to be free from defective workmanship and materials for
the first year following the date of original purchase. Replacement parts will be supplied free of
charge for the first year following the date of original purchase. Labor will be performed free of
charge for the first 90 days following the date of original purchase.
WHAT IS COVERED:
This warranty applies to the original purchaser only, and only covers defects in workmanship
experienced during operation of the product under normal service, maintenance, and usage
conditions. This warranty applies to the purchase and use of this product in residential settings
within the United States of America.
WHAT IS NOT COVERED:
The following limitations apply to the coverage of this warranty:
Optional accessories, attachments, and appearance items are excluded from warranty coverage,
as is shipping damage, and any damage caused by improper voltage or any other misuse,
including abnormal service, handling, or usage.
This warranty does not cover normal wear and tear on parts or replacement of parts designed to
be replaced, e.g. filters, etc.
This warranty does not cover service trips to deliver, pick-up, repair, or install the product, or
to instruct in proper usage of the product.
Damages or operating problems resulting from abuse, operation outside environmental
specifications, uses contrary to instructions provided in the owner’s manual, accidents, vermin,
fire, flood, improper installation, unauthorized service, acts of God, unauthorized installation
or modification, or commercial use are excluded from warranty coverage.
Damage or loss of items stored inside the appliance are excluded from warranty coverage.
This warranty does not cover labor incurred 91 days or more after the date of original purchase.
This warranty does not cover use of EdgeStar products in commercial settings.
DESCRIPTION OF WARRANTY SERVICE:
All defective product components covered by this warranty will be repaired or replaced, at
EdgeStar’s option, free of charge on a mail-in basis to EdgeStar’s authorized repair facility
during the first 90 days from the date of original purchase.
All defective product components covered by this warranty will be repaired or replaced, at
EdgeStar’s option, on a mail-in basis to EdgeStar’s authorized repair facility during the time
period beginning on the 91st day from the date of original purchase and ending one year from
the date of original purchase. During this time period, parts will be supplied free of charge, but
labor charges will apply.
All replacement parts and units will be new, remanufacturered, or refurbished.
All products and components replaced by EdgeStar under warranty service become the
property of EdgeStar.
OBTAINING WARRANTY SERVICE:
Contact EdgeStar for troubleshooting assistance and warranty service authorization at
1-866-319-5473. Please have your order receipt available to confirm the date of purchase.
Once an EdgeStar authorized representative has confirmed that your product is eligible for
warranty service, the product must be returned to an EdgeStar authorized repair facility.
The purchaser is solely responsible for prepaying all shipping related costs to and from the
repair facility.
6
EdgeStar is not responsible for damage resulting from shipper mishandling or improper
packaging.
Do not return defective product to the place of purchase.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED
WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE
EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS
DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL,
INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING
WITHOUT LIMITATION, LOST REVENUES OR PROFITS, OR ANY OTHER DAMAGE
WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. SOME STATES DO NOT
ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY
FROM STATE TO STATE.
7
|