Upright
Vacuum Cleaner
Household Type
Owner’s Guide
1400-1900 Series
Index
Important Safeguards......................... 2
Service Information ............................ 4
Assemble ........................................... 5
Order Form.................................. Insert
Use ................................................... 11
Dust Bag .......................................... 12
Brush Roll Belt ................................. 13
Brush Roll......................................... 14
Headlight .......................................... 14
Warranty........................................... 15
For location of nearest Eureka
Warranty Station or service
information call
1-800-282-2886*.
*En Mexico llame al 5670-6169
CONSEILS DE SÉCURITÉ
Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent
être observées, incluant les suivantes:
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER VOTRE ASPIRATEUR.
AVERTISSEMENT
Pour réduire le risque de feu, de choc électrique, ou de blessure:
• Ne pas utiliser à l’extérieur ou sur des surfaces mouillées.
• Fermez le commutateur et débranchez l’appareil lorsque vous ne l’utilisez pas ou
avant le nettoyage ou l’entretien.
• Ne permettez pas qu’il soit utilisé comme jouet. Une attention particulière est nécessaire
lorsque utilisé par ou près d’un enfant.
• Suivez les recommandations d’utilisation de ce manuel. Utilisez uniquement les
accessoires recommandés par le fabriquant.
• Ne pas utiliser si le cordon ou la fiche sont endommagés. Si l’aspirateur ne fonctionne
pas comme il le devrait, s’il a été échappé, s’il est endommagé, s’il a été laissé à l’extérieur
ou échappé dans l’eau, retournez-le à un centre de service avant de utiliser.
• Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de
poignée. Ne pas fermer une porte sur le cordon ou tirer le cordon sur des coins ou
bordures pointus. Ne pas circuler sur le cordon avec l’aspirateur. Tenir le cordon à
distance des surfaces chauffantes.
• Ne pas utiliser des rallonges ou des prises qui n’ont pas de capacité suffisante pour
transporter le courant.
• Fermer tous les contrôles avant débrancher.
• Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le
cordon.
• Ne pas manipuler la fiche ou l’aspirateur avec les mains mouillées.
• Ne pas rien insérer dans les ouvertures. Ne pas utiliser si des ouvertures sont bloquées;
assurez-vous qu’elles soient dégagées de poussière, mousse, cheveux ou toute autre
chose qui pourrait réduire le passage de l’air.
• Cet aspirateur crée de la succion et contient un rouleau-brosse tournant. Tenir les parties
mobiles et les ouvertures loin des cheveux, du linge, des doigts et de toute partie du
corps.
• Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, allumettes ou
cendres chaudes.
• N’utilisez pas sans le sac de poussière en place.
• Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour
prévenir des brûlures, évitez de touché la poulie du courroie lorsque vous réparez la
courroie.
• Portez une attention particulière lorsque vous nettoyez les escaliers.
• Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de
l’essence: Ne pas utiliser dans les endroits où ces liquides pourraient être présents.
• Entreposez votre aspirateur à l’intérieur dans un endroit propre et sec.
• Maintenez un bon éclairage à l’endroit où vous travaillez.
• c Débrancher les appareils électrique avant de les balayer.
CONSERVEZ CES INSTRUCTIONS
3
To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche
polarisée (une des lames est plus large). Cette fiche ne peut être insérée dans une
prise polarisée que d’une seule façon. Si la fiche ne peut être insérée dans la prise,
retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire
installer une prise adéquate par un électricien qualifié. Ne pas modifier la fiche.
GENERAL INFORMATION
The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or
sharp objects with the cleaner to prevent bag tears, hose clogs, and fan blade breakage
with subsequent motor damage.
Service Information
The instructions in this booklet serve as a guide to routine maintenance. For additional
service information telephone our toll free number for the nearest Eureka Authorized
Warranty Station. You should know the model, type and serial numbers when you
call:
USA: 1-800-282-2886
México: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main
Street, Bloomington, Illinois 61701, USA. In Canada write to The Eureka Company,
866 Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka Limited Warranty
for complete service information.
DO NOT OIL the motor or the brush roll at any time. The bearings are
permanently lubricated and sealed.
Rating Plate
The model, type, and serial numbers are
MODEL
VOLTS
TYPE
SERIAL NO.
HERTZ
indicated on the rating plate located on the
underneath side of the cleaner. For prompt and
complete service information, always refer to
these numbers when inquiring about service.
AMPS.
SERVICE INFORMATION: 1-800-282-2886
THE EUREKA COMPANY
BLOOMINGTON, ILLINOIS 61701
Model & Type_________________________
Serial No.____________________________
4
HOW TO ASSEMBLE
CAUTION: Completely assemble vacuum cleaner before using.
Handle styles may vary. One handle
Assembly Packet
has four snap pins on the back side
of the handle, the other handle has
two snap pins on each side. The cord
hooks may be different.
A - CONNECTOR
Step 1 - Handle Connector
B -
FASTENER
C - 2-PART D - BAG
BOLT
SCREWS
Push connector A into the upper
handle and align holes. One
connector, shown, is flat on one side
and the 4 pins snap into one side. The
connector in Detail A has 2 snap pins
on each side and alignment tabs that
slide into the handle.
Step 2 - Fastener
Push fastener B into a hole and apply
thumb pressure so fastener snaps into
position. Secure second fastener.
Repeat steps 1 and 2 to complete the
assembly of the handle. See Detail B.
B
A
B
Tab
Detail A
Detail B
E
Step 3 - Handle Socket
C–
Push handle into handle socket E so
handle grip curves away from the
cleaner. Align the holes, insert the 2-
part bolt C and tighten.
5
Step 4 - Outer Bag
Hold outer bag with zipper away from
handle. Important: To provide a
good gasket seal, the bag
coupling must seat firmly against
the motor base and not overlap
the furniture guard. Start the bag
screws D by hand, then tighten with
a screwdriver.
Step 5 - Bag Support
Loop the spring F onto the bag
support G, located to the back of the
upper cord hook.
G
Upper
Guide
Upper Cord
Hook
F
E
Lower Cord
Hook
C–
D
Step 6 - Cord Storage
Secure the cord in the guide below the
upper cord hook as shown or secure
the cord into the side of the upper cord
hook.
Secure cord into lower cord hook. Pull
up on cord to tighten but leave slack
near the base so the cord does not
strain when the handle is lowered for
use. Wrap the cord around the cord
hooks. Fasten the plug to the cord to
prevent unwinding.
6
HOW TO USE
The upright vacuum cleaner is designed to be used on multiple types of carpeting. Do
not attempt to use the upright vacuum cleaner on bare floors, as damage to the
floor covering may result. Above the floor cleaning tools are available (optional).
1. Store
2. Use
Handle Adjustment
With the tip of the foot, press down to
release the handle lock located at the left
rear side of the cleaner. Move the handle
and adjust it to the desired position for (1)
storing upright, (2) operating the cleaner at
a comfortable height for the user, and (3)
cleaning underneath low furniture.
3.Clean
Underneath
Handle Lock
ON/OFF
Power Switch
The power switch is mounted on the motor
hood. A push with the foot turns the motor
ON; push again to turn the motor OFF.
Cord Storage
The cleaner has two convenient cord
storage hooks attached to the handle.
However, some models feature a quick
release cord hook on the upper handle. A
downward twist of the cord hook frees the
cord for quick removal. With either style,
wind the cord around the hooks for storage.
Fasten the plug to the cord to prevent
unwinding.
Cleaner Height Setting
WARNING: Avoid injury. Keep loose clothing, hair, fingers, and all other parts
of body away from any moving part (such as the revolving brush).
Turn off the switch and unplug the cleaner before changing the
cleaner height setting.
The front of the cleaner has an adjustment that
raises or lowers the cleaner base to match the
type of carpet. With the cleaner cord unplugged,
set the adjustment to lowest setting for maximum
cleaning. If the cleaner is difficult to push, move
adjustment to next highest setting until cleaner
is comfortable to push. The brush roll must reach
the carpet for effective cleaning.
Make each adjustment with
cleaner switch off and cord
disconnected from outlet. For
ease in moving the adjustment
knob, place handle in operating
position and tilt cleaner back to
remove weight from front wheels.
11
HOW TO MAINTAIN
The instructions given in this booklet serve as a guide to routine maintenance. To
avoid unnecessary service calls, check the bag, belt and brush roll often.
Disposable Dust Bags
Paper bags play a very important role in the efficiency of a vacuum cleaner. The purpose
of a paper bag is to trap dirt. But at the same time the bag must be porous enough to
allow air to pass through. If the paper bag becomes clogged, no air can pass through
the cleaner and no cleaning can take place, regardless of how powerful the unit is.
Change the dust bag frequently. Some fine particles can restrict airflow very quickly
and will decrease performance even before the bag appears to be full. For that reason,
when vacuuming carpet fresheners or cleaners, powder, plaster dust, or similar fine
substances, the bag may need to be changed more often.
How To Change Disposable Dust Bag–Style F & G
NOTE: Turn off the switch and unplug the electrical cord before changing dust
bag. Never operate the vacuum cleaner without the dust bag.
4. Unfold
new
bag
THROAT
1. Pull
zipper
2. Roll
down
down
coil
spring
3. Pull bag
throat off
sleeve
s
5. Place bag
throat on
sleeve
6. Roll up
coil spring
7. Place paper bag into outer bag.
NOTE: Be certain there are no folds
at the top or bottom of the
paper bag.
GENUINE
EUREKA PRODUCT
Look for the
symbol.
8. Lift zipper
Ask for GENUINE EUREKA
dust bags–Style F & G.
Cleaner Care
NOTE: Turn off the switch and unplug the electrical cord before cleaning unit.
To keep the vacuum cleaner looking new, it can be wiped with a damp cloth and a mild
soap solution, then thoroughly dried. Never use any type of chemical as chemicals
can damage the cleaner. When not in use, the cleaner should be stored in a clean, dry
place.
12
Brush Roll Belt
The brush roll belt on the upright vacuum cleaner drives the brush to agitate, sweep,
and comb the carpet nap. The belt should be checked regularly to be sure it is in good
condition. Replace the belt if it is stretching, cracking, or slipping. Cut away any hair or
thread wound around the brush roll or the belt pulley because the buildup could cause
the belt to rotate unevenly.
How To Replace A Worn Belt
NOTE: Turn off the switch and unplug the electrical cord before replacing belt.
Belt pulleys can become hot during normal use. To prevent injury, avoid
touching the belt pulley when servicing the drive belt.
IMPORTANT: Improper installation of the brush roll or brush roll belt could cause
carpet or cleaner damage.
Motor
2
Pulley
1
1
1. Release cam locks.
2. Pull up on belt to rotate it off the
motor pulley. Lift up on brush roll
and remove worn belt.
Belt
Guide
5
4
3
6
Brush Roll Pulley
Check for brush wear, see Brush
Roll instructions.
5. Place rubber end cap covers over
both end caps (flat side against end
cap). Align holes and secure. Then,
slant brush roll forward so end
caps are in line with slots in cleaner
base.
3. Place new belt around
brush roll.
4. Align brush roll pulley with
belt guide.
6. Push brush roll into base
7
9
9
7. Place lower side of belt
into belt guide and pull to
stretch the belt around the
left side of the motor
pulley. Rotate pulley to
secure belt into groove.
8
8
8. Place slots of bottom plate over
tabs of cleaner base.
9. Seat and secure cam locks
GENUINE
Ask for GENUINE EUREKA
replacement belts No. 52100.
EUREKA PRODUCT
Look for the
symbol.
13
Brush Roll
The rotating brush roll sweeps and combs the carpet nap. Keep the brush roll free
from hair and threads so it will continue brushing. When the bristles of the brush roll no
longer touch a straight edge held against the bottom plate, the brush roll is ineffective
because the bristles no longer touch the carpet nap. To maintain the most effective
cleaning, the brush roll should be replaced.
Headlight Bulb (Standard on most models)
NOTE: Turn off the switch and unplug the electrical cord before replacing
headlight bulb.
Headlight style varies by model. Locate the notches that release the tabs at either (1)
top, (2) side, or (3) bottom of the lens, as illustrated. Place a screwdriver into one
notch; twist or pry the screwdriver to release the lens. Repeat for the second notch on
the opposite side.
Rotate the bulb socket forward. Push bulb in and turn to remove. Secure new bulb into
socket and rotate bulb socket backward.
Replace the lens tabs into the top or the bottom of the hood opening. Rotate lens to
position and press down at notch until the lens locks into position.
NOTE: Use 25 watt replacement bulb, only.
Ask for GENUINE EUREKA replacement bulb, 40009A.
1
2
3
14
RANTY
LMITEDW
THUREKA
(s58779)
©1999 White Consolidated Industries, Inc.
Printed in U.S.A.
Part No. 58331A (2/01)
|