2
General
Preparation
1. Never allow children or people unfamiliar
with these instructions to use the
Hedgetrimmer. Local regulations may
restrict the age of the operator.
2. Only use the Hedgetrimmer in the manner
and for the functions described in these
instructions.
1. Always wear suitable clothing, gloves, and
stout shoes. The use of safety glasses is rec-
ommended. Do not wear loose clothing or
jewellery which can be caught in moving parts.
2. Thoroughly inspect the area where the
Hedgetrimmer is to be used and remove all
wires and other foreign objects.
3. Never operate the Hedgetrimmer when you
are tired, ill or under the influence of alcohol,
drugs or medicine.
3. Before using the machine and after any
impact, check for signs of wear or damage
and repair as necessary.
4. The operator or user is responsible for acci-
dents or hazards occurring to other people
or their property.
4. Never attempt to use an incomplete
Hedgetrimmer or one with an unauthorised
modification.
Electrical
Use
1. The British Standards Institute recommend
1. Use the Hedgetrimmer only in daylight or
the use of a Residual Current Device (R.C.D.)
good artificial light.
with a tripping current of not more than 30mA. 2. Avoid operating your Hedgetrimmer on a
Even with a R.C.D. installed 100% safety
cannot be guaranteed and safe working prac-
tice must be followed at all times. Check your
R.C.D. every time you use it.
wet hedge, where feasible.
3. Know how to stop the Hedgetrimmer quickly
in an emergency.
4. Never hold the Hedgetrimmer by the guard.
5. Never operate the Hedgetrimmer with dam-
aged guards or without guards in place.
6. Remove plug from mains before passing
Hedgetrimmer to another person.
7. Avoid operating while people especially chil-
dren are nearby.
8. Whilst using the Hedgetrimmer always be
sure of a safe and secure operating position.
2. Before use, examine cable for damage,
replace it if there are signs of damage or
ageing.
3. Do not use the Hedgetrimmer if the electric
cables are damaged or worn.
4. Immediately disconnect from the mains elec-
tricity supply if the cable is cut, or the insula-
tion is damaged. Do not touch the electric
cable until the electrical supply has been dis- 9. Keep hands and feet away from the cutting
connected. Do not repair a cut or damaged
cable. Replace it with a new one.
5. Your electric cable must be uncoiled, coiled
cables can overheat and reduce the efficien-
cy of your Hedgetrimmer.
means at all times and especially when
switching on the motor.
10. Do not use stepladders whilst operating the
Hedgetrimmer.
11. Remove the plug from the mains :-
6. Keep cable away from the cutting area.
7. Never carry the product by the cable.
8. Never pull on the cable to disconnect any of
the plugs
9. Do not pull cable around sharp objects.
10. Always switch off at the mains before dis-
connecting any plug, cable connector or
extension cable.
11. Switch off, remove plug from mains and
examine electric supply cable for damage or
ageing before winding cable for storage. Do
not repair a damaged cable, replace it with a
new one. Use only Flymo replacement
cable.
-
before leaving the Hedgetrimmer unattended
for any period;
before clearing a blockage;
before checking, cleaning or working on the
appliance;
if you hit an object. Do not use your
Hedgetrimmer until you are sure that the
entire Hedgetrimmer is in a safe operating
condition;
-
-
-
-
-
if the Hedgetrimmer starts to vibrate abnor-
mally. Check immediately. Excessive vibra-
tion can cause injury.
before passing to another person.
Maintenance and storage
12. Always wind cable carefully, avoiding kink-
ing.
13. Use only on AC mains supply voltage shown
on the product rating label.
14. Our products are double insulated to
EN60335. Under no circumstances should
an earth be connected to any part of the
product.
1. Keep all nuts, bolts and screws secure to be
sure the Hedgetrimmer is in safe working
condition.
2. Replace worn or damaged parts for safety.
3. Be careful during adjustment of the
Hedgetrimmer to prevent entrapment of the
fingers between moving blades and fixed
parts of the machine.
4. After use the Hedgetrimmer should be
stored using the blade cover/storage holder
provided.
3
CABLES
3. IMPORTANT!
IMPORTANT
• Use only 1.00mm2 size cable up to 30
E
metres length maximum.
L
RED
OR
BROWN
Maximum rating :
F
U
S
1.00mm2 size cable, 10 amps 250 volts AC.
BLACK
E
OR
N
• YOUR HEDGETRIMMER IS SUPPLIED
WITH CABLE WIRED DIRECTLY INTO
THE PRODUCT.
BLUE
1. Flymo Mains Cables and Extension Cables
are available from your local Electrolux
Outdoor Products Approved Service
Centre.
The wires in the mains lead are coloured in
accordance with the following code:
2. Do not wire an extension cable directly to
your product yourself. Please contact your
local Electrolux Outdoor Products Approved
Service Centre for further information on
the connectors and kits available.
BLUE
BROWN
-
-
NEUTRAL
LIVE
The wire which is coloured BLUE must be
connected to the Terminal which is marked
with the letter 'N' or coloured BLACK.
The wire which is coloured BROWN must
be connected to the Terminal which is
marked with the letter 'L' or coloured RED.
3. Only use extension cables specifically
designed for outdoor use.
CONNECTORS
IMPORTANT
4. It is important that the outer sheath is
clamped correctly into the 3-pin plug.
• Flymo connectors are suitable for use with
2 core cable only. Under no circumstances
should these connectors be used for earth-
ed products.
5. If in doubt consult your local Service
Repairer or qualified electrician before the
machine is used.
6. A 13 Amp fuse must be fitted to the
Mains Plug.
• All Flymo connectors and cables are of
splashproof construction. They are not
waterproof and must not be left outside per-
manently nor should they be submerged or
immersed in water. Do not let cable lay or
trail through pools of water or splashed with
water from hose pipes.
7. The normal plug fuse and household fuse
only protect the electrical equipment and
are not a safeguard against electrocution.
If your product is hard wired i.e. non-
detachable mains electric cable, a conver-
sion kit and extension cable is available
from all Electrolux Outdoor Products
Approved Service Centres which can be
found in your local Yellow Pages.
MAINS PLUG REPLACEMENT
IMPORTANT
• If the plug supplied is cut off it should
be destroyed. There is an electric shock
hazard if a cut off plug is inserted into a
13 amp socket.
1. No earth required. Flymo products are
double insulated to EN60335 and under no
circumstances should an earth be connect-
ed to any part of the product.
2. Ensure the mains voltage suits your
product
4
Starting and Stopping
Before starting your Hedgetrimmer.
A
C
D
B
1. Form a loop in mains cable and push the
loop through the hole in the handle as
illustrated in Fig. A.
2. To secure, position the loop over the hook
and pull back as illustrated in Fig. B.
3. Connect to mains and switch on
4. Remove blade cover as illustrated in Fig.
C.
To start your Hedgetrimmer
1. There are two switch levers fitted to your
Hedgetrimmer.
2. Both switch levers need to be held in the
operating position (See Fig D) for the
product to start.
E
To stop your Hedgetrimmer
•
Move Hedgetrimmer away from cutting
area before stopping.
1. To stop, release one of the switch
levers.(Fig E)
How to Use
F
How to Use your Hedgetrimmer
1. Inspect area to be cut before each use -
remove objects which can be thrown or
become entangled in the cutting blades.
2. Always keep the Hedgetrimmer in front of your
body. Hold handle firmly with both hands and
stand in a secure and stable position.
3. Allow the cutting blades to reach full speed
before entering the material to be cut.
4. Always work going away from people and solid objects
such as walls, large stones, trees, vehicles etc.
5. If blade stalls, immediately stop the
Hedgetrimmer. Disconnect the Hedgetrimmer
from the power source and clear jammed
debris from the cutting blades. Inspect blades
and repair or replace as needed.
G
Top Cutting
Use a wide sweeping motion. See Fig. F. A
slight downward tilt of the cutting blades in the
direction of motion gives the best cutting results.
Side Cutting
When trimming the sides of the hedge, begin at the
bottom and cut upwards (See Fig. G), tapering the
hedge inward at the top. This shape will expose more
of the hedge, resulting in more uniformed growth.
5
Caring for your Hedgetrimmer
Cleaning (H)
1. Using a soft brush - remove debris from all
H
air intakes and cutting blade.
2. Wipe over surface of your hedgetrimmer
with a dry cloth.
•
IMPORTANT
Never use water for cleaning your hed-
getrimmer. Do not clean with chemicals,
including petrol, or solvents - some can
destroy critical plastic parts.
Lubricating the Cutting Blade
For easier operation and longer life, lubricate
the cutter blades before and after use. Apply
the oil so that it runs between the two blades.
See Pic J.
J
At the end of the Cutting Season.
1. Clean your Hedgetrimmer thoroughly.
2. Check that all nuts and bolts are secure.
3. Visually inspect the Hedgetrimmer for any
worn or damaged parts, contact your local
Service Centre if any parts require
replacement.
K
To store your Hedgetrimmer
•
Ensure the blade cover is fitted before
storage. (Pic K)
•
Store in a dry place where your
Hedgetrimmer is protected from damage.
Fault Finding Hints
Fails to Operate
Poor cut quality
1. Is the Power Turned On?
1. Ensure the product is being used correctly
2. Check the fuse in the plug, if blown replace.
3. Fuse continues to blow?
Immediately disconnect from the mains
electricity supply and consult your local
approved Service Centre.
(see How to Use)
2. Ensure blades are free from trapped debris
3. Damaged Blades?
Immediately disconnect from the mains
electricity supply and consult your local
approved Service Centre.
Cutting blade stops under load
1. Cut at a slower pace.
Excessive Vibration
2. If cutting blade still stops under load?
Disconnect from the mains electricity
supply and consult your local approved
Service Centre.
Immediately disconnect from the mains
electricity supply and consult your local
approved Service Centre.
Fails to stop when one switch lever is
released.
Immediately disconnect from the mains
electricity supply and consult your local
approved Service Centre.
6
Environmental Information
Electrolux Outdoor Products are manufac-
tured under an Environmental Management
System (ISO 14001) using, where practical,
components manufactured in the most envi-
ronmentally responsible manner, according to
company procedures, and with the potential
for recycling at the end of the products’ life.
ponents have been labelled (where practi-
cal) for categorised recycling.
•
•
Awareness of the environment must be
considered when disposing of ‘end-of-life’
product.
If necessary, contact your local authority
for disposal information.
•
Packaging is recyclable and plastic com-
Service Recommendations
1. We strongly recommend that your product
is serviced at least every twelve months,
more often in a professional application.
2. Always use genuine Flymo Spare Parts.
3. Prepacked spares are available from most
Electrolux Outdoor Products stockists.
4. Your product is uniquely identified by a sil-
ver and black product rating label
take your complete machine including cable
and any extension cables used.
A network of specialist dealers can be found in
your local Yellow Pages. To obtain service on
your Flymo product simply telephone or visit your
local Service Centre. Should you require service
under the terms of our guarantee the Service
Centre will require proof of purchase.
5. If you have a problem with your machine
contact your local Approved Service Centre
All of the centres listed stock genuine Flymo
Spare Parts.
ensuring you have full details of your product NOTE: Our Service Repairers act on their own
as described on the product rating label.
6. Should it be necessary for work to be carried
out by your Service Centre, it is important to
behalf and are not empowered to commit or
legally bind Electrolux Outdoor Products in
any manner whatsoever.
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty man-
ufacture within the guarantee period, Electrolux
Outdoor Products, through its Authorised Service
Repairers will effect the repair or replacement to the
customer free of charge providing:
(a) The fault is reported directly to the Authorised
Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or
faulty adjustment by the user.
(d) The failure has not occurred through fair wear
and tear.
(e) The machine has not been serviced or
repaired, taken apart or tampered with by
any person not authorised by Electrolux
Outdoor Products.
Failures not covered by guarantee
* Replacing worn or damaged blades
* Failures as a result of not reporting an initial
fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in
accordance with the instructions and recom-
mendations contained in this Operator's
Manual.
* Machines used for hire are not covered by this
guarantee.
* The following items listed are considered as
wearing parts and their life is dependent on
regular maintenance and are, therefore not
normally subject to a valid warranty claim:
Blades, Electric Mains cable.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used outside of
the country for which it was specified.
(i) The machine has not been used commercially.
* Caution!
Electrolux Outdoor Products does not accept
liability under the warranty for defects caused
in whole or part, directly or indirectly by the fit-
ting of replacement parts or additional parts
that are not either manufactured or approved
by Electrolux Outdoor Products, or by the
machine having been modified in any way
*
This guarantee is additional to, and in no way
diminishes the customers statutory rights.
Failures due to the following are not covered, therefore
it is important that you read the instructions contained in
this Operator's Manual and understand how to operate
and maintain your machine:
Declaration of Conformity
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP. Certify that the product:-
Category........ Hedgetrimmer
Make.............. Electrolux Outdoor
Products
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP Certify that a sample of the above
product has been tested using directive
81/1051/EEC as a guide. The maximum A-
weighted sound pressure level recorded at
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP Certify that a sample of the above
product has been tested using ISO 5349 as
a guide. The maximum weighted root mean
square value of vibration recorded at opera-
tor’s hand position was:-
Conforms to the specifications of Directive operator position under free field semi ane-
2000/14/EEC
choic chamber conditions was :-
Identification of Series......See Product Rating Label
Conformity Assessment Procedure....ANNEX VI
Notified Body.................... I.T.S., Cleeve Road, Leatherhead,
Surrey. KT22 7SB England
Other Directives:-............. 98/37/EEC, 89/336/EEC, 73/23/EEC
& applicable standards:-. EN60555-2:1987, EN60555-3:1987,
EN55014:1993, EN55014:1995, EN774:1996, EN50144-1:1995,
EN50144-2-15:1997
Type............................................................................ A
Blade Length..............................................................
Guaranteed sound power level................................... C
Measured Sound Power Level.................................... D
Level............................................................................ E
B
Value...........................................................................
Weight.........................................................................
F
G
A
A
HT39
HT42
42 cm
B
C
D
E
F
39 cm
B
C
D
E
F
100 dB (A)
97 dB (A)
91.6 dB(A)
98 dB (A)
96 dB (A)
89.5 dB(A)
2
2
5.05 m/s
6.58 m/s
G
2.4 kg
G
2.4 kg
A
B
C
D
E
F
A
B
C
D
E
F
HT42s
42 cm
HT45s
45 cm
98 dB (A)
96 dB (A)
89.5 dB(A)
99 dB (A)
97 dB (A)
89.5 dB(A)
2
2
6.58 m/s
6.58 m/s
G
2.4 kg
G
2.5 kg
A
HT53s
53 cm
B
C
D
E
F
104 dB (A)
98 dB (A)
89.5 dB(A)
Newton Aycliffe, 01/08/2002
M. Bowden,
2
6.58 m/s
Research & Development Director
G
2.6 kg
Electrolux Outdoor Products
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Telephone - (00) 44 1325 300303 Fax - (00) 44 1325 310339
UK Customer Helpline - 01325 300303 Fax - 01325 310339
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Electrolux Outdoor Products manufacture products for a number of well known brands under various registered patents, designs and
trademarks in several countries.
© Electrolux Outdoor Products Ltd. Registered Office, Electrolux Works, Oakley Road, Luton LU4 9QQ
Registered number 974979 England
The Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million
Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold
each year to a value of approx. USD 14 billion in more than 150 countries around the world.
5118646-06
|