GEAppliances.com
Safety Information . . . . . . . . . 2
Owner’s Manual
Warranty. . . . . . . . . . . . . . . . . . . . . 6
Assistance / Accessories . . . 7
PT7050 - 30" Single Wall Oven
PT9050 - 30" Single Wall Oven
PT7550 - 30" Double Wall Oven
PT9550 - 30" Double Wall Oven
Using The Oven
Oven Controls. . . . . . . . . . . . . . . . . . . 8
Special Features . . . . . . . . . . . . . . . 10
Oven Racks . . . . . . . . . . . . . . . . . . . . 12
Cooking Modes . . . . . . . . . . . . . . . . 14
Cookware. . . . . . . . . . . . . . . . . . . . . . 15
Cooking Guide . . . . . . . . . . . . . . . . . 16
Care and Cleaning
Control Panel . . . . . . . . . . . . . . . . . . 17
Oven Exterior . . . . . . . . . . . . . . . . . . 17
Stainless Steel Surfaces . . . . . . . . 17
Oven Interior. . . . . . . . . . . . . . . . . . . 17
Oven Racks . . . . . . . . . . . . . . . . . . . . 18
Maintenance. . . . . . . . . . . . . . . . . . . 19
Troubleshooting Tips . . . . . . 22
For a Spanish version of this
manual, visit our Website at
GEAppliances.com.
Write the model and serial
numbers here:
Model # __________________
Serial # ___________________
Para consultar una version
en español de este manual
de instrucciones, visite
nuestro sitio de internet
GEAppliances.com.
You can find them on a label
on the side trim or on the front of
the (lower) oven behind the oven
door.
Printed on
Recycled Paper
Printed in the United States
49-80668-2 04-13 GE
KEEP FLAMMABLE MATERIALS AWAY FROM THE OVEN
WARNING
Failure to do so may result in fire or personal injury.
■
Do not store or use flammable materials in or near
an oven, including paper, plastic, pot holders,
linens, wall coverings, curtains, drapes and
gasoline or other flammable vapors and liquids.
■
Never wear loose-fitting or hanging garments while
using the appliance. These garments may ignite if
they contact hot surfaces, causing severe burns.
■ Do not let cooking grease or other flammable
materials accumulate in or near the oven.
Grease in the oven or near the oven may ignite.
IN THE EVENT OF A FIRE, TAKE THE FOLLOWING
STEPS TO PREVENT INJURY AND FIRE SPREADING
WARNING
■ Do not use water on grease fires. Never pick up ■ If there is a fire in the oven during self-clean,
a flaming pan.
turn the oven off and wait for the fire to go out.
Do not force the door open. Introduction of fresh
air at self-clean temperatures may lead to a
burst of flame from the oven. Failure to follow
this instruction may result in severe burns.
■ If there is a fire in the oven during baking,
smother the fire by closing the oven door and
turning the oven off or by using a multi-purpose
dry chemical or foam-type fire extinguisher.
OVEN SAFETY INSTRUCTIONS
WARNING
■ Stand away from the oven when opening the
oven door. Hot air or steam which escapes can
cause burns to hands, face and/or eyes.
■ Keep the oven vent unobstructed.
■ Keep the oven free from grease buildup.
■ Pulling out the standard racks to their stop-locks
or the extension rack to its fully open position is
a convenience in lifting heavy foods. It is also
a precaution against burns from touching hot
surfaces of the door or oven walls.
■ Do not leave items such as paper, cooking
utensils or food in the oven when not in use.
Items stored in an oven can ignite.
Grease in the oven may ignite.
■
Place oven racks in desired location while oven is
cool. If rack must be moved while oven is hot, do not
let pot holder contact hot heating element in oven.
■
Do not use aluminum foil to line the oven bottom.
Foil can trap heat or melt, resulting in damage to
the product and a shock or fire hazard.
■ When using cooking or roasting bags in the
oven, follow the manufacturer’s directions.
SELF-CLEANING OVEN SAFETY INSTRUCTIONS
The self-cleaning feature operates the oven at temperatures high enough to burn away food soils in the
WARNING
oven. Follow these instructions for safe operation.
■ If the self-cleaning mode malfunctions, turn the
oven off and disconnect the power supply. Have
it serviced by a qualified technician.
■ Do not clean the door gasket. The door gasket
is essential for a good seal. Care should be
taken not to rub, damage or move the gasket.
■ Do not use oven cleaners. No commercial oven
cleaner or oven liner protective coating of any
kind should be used in or around any part of the
oven.
■ Do not touch oven surfaces during self-clean
operation. Keep children away from the oven
during self-cleaning. Failure to follow these
instructions may cause burns.
■ Before self-cleaning the oven, remove shiny
silver colored oven racks (on some models), the
probe, any aluminum foil, and any broiler pan,
grid, and other cookware. Only porcelain coated
oven racks may be left in the oven.
■ Before operating the self-clean cycle, wipe
grease and food soils from the oven. Excessive
amount of grease may ignite, leading to smoke
damage to your home.
SAVE THESE INSTRUCTIONS
3
49-80668-2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
The remote enable equipment installed on this oven
has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to:
■
Reorient or relocate the receiving antenna.
■
Increase the separation between the equipment
and receiver.
■
■
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
(a) provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
Consult the dealer or an experienced radio/TV
technician for help.
(b) accept any interference received, including
interference that may cause undesired operation of
the device.
Note that any changes or modifications to the remote
enable device installed on this oven that are not
expressly approved by the manufacturer could void
the user's authority to operate the equipment.
4
49-80668-2
Notes
5
49-80668-2
Thank You! ... for your purchase of a GE Brand appliance.
Register Your Appliance: Register your new appliance on-line at your convenience!
Timely product registration will allow for enhanced communication and prompt service under the terms of your
warranty, should the need arise. You may also mail in the pre-printed registration card included in the packing material.
GE Electric Range Warranty
GEAppliances.com
All warranty service is provided by our Factory Service Centers, or an authorized Customer Care® technician.
To schedule service on-line, visit us at www.geappliances.com/service_and_support/, or call 800.GE.CARES
(800.432.2737). Please have serial number and model number available when calling for service.
Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a GE factory
service technician the ability to quickly diagnose any issues with your appliance and helps GE improve its products
by providing GE with information on your appliance. If you do not want your appliance data to be sent to GE, please
advise your technician not to submit the data to GE at the time of service.
For the period of one year from the date of the original purchase. GE will provide any part of the range which fails
due to a defect in materials or workmanship. During this limited one-year warranty, GE will also provide, free of
charge, all labor and in-home service to replace the defective part.
What GE will not cover:
■ Service trips to your home to teach you how to use
the product.
■ Damage to the product caused by accident, fire,
floods or acts of God.
■ Improper installation, delivery or maintenance.
■ Failure of the product if it is abused, misused,
■ Incidental or consequential damage caused by
possible defects with this appliance.
modified or used for other than the intended purpose ■ Damage caused after delivery.
or used commercially.
■ Product not accessible to provide required service.
■ Replacement of house fuses or resetting of circuit
breakers.
EXCLUSION OF IMPLIED WARRANTIES
Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties,
including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the
shortest period allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available,
you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service
location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal
rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
Extended Warranties: Purchase a GE extended warranty and learn about special discounts that are available
while your warranty is still in effect. You can purchase it on-line anytime
or call 800.626.2224 during normal business hours. GE Consumer Home Services will still be there after your
warranty expires.
6
49-80668-2
Have a question or need assistance with your appliance?
Try the GE Appliances Website (www.geappliances.com/service_and_support/) 24 hours a day, any day of the
year! For greater convenience and faster service, you can now download Owner’s Manuals, order parts or even
schedule service on-line.
Schedule Service: Expert GE repair service is only one Caution must be exercised, since improper servicing
step away from your door. Get on-line and schedule
support/ Or call 800.GE.CARES (800.432.2737) during
normal business hours.
may cause unsafe operation.
Real Life Design Studio: GE supports the Universal
Design concept of products, services and environments
that can be used by people of all ages, sizes and
capabilities. We recognize the need to design for a wide
range of physical and mental abilities and impairments.
For details of GE’s Universal Design applications,
including kitchen design ideas for people with disabilities,
check out our Website today. For the hearing impaired,
please call 800.TDD.GEAC (800.833.4322).
Remote Connectivity: For assistance with oven
wireless network connectivity (for models with remote
enable) , please call 1-800-220-6899.
Parts and Accessories: Individuals qualified to service
their own appliances can have parts or accessories sent
directly to their homes (VISA, MasterCard and Discover
cards are accepted).Order on-line today, 24 hours
every day or by phone at 800.626.2002 during normal
business hours.
Contact Us: If you are not satisfied with the service you
receive from GE, contact us on our Website with all the
details including your phone number, or write to:
Instructions contained in this manual cover procedures
to be performed by any user. Other servicing generally
should be referred to qualified service personnel.
General Manager, Customer Relations
GE Appliances, Appliance Park Louisville, KY 40225
Accessories
Looking For Something More?
GE offers a variety of accessories to improve your cooking and maintenance experiences!
To place an order visit us online at:
or call 800.626.2002 (U.S.) 800.661.1616 (Canada)
The following products and more are available:
Accessories
Small Broiler Pan (8 ¾ ” x 1 ¼” x 13 ½ “)
Large* Broiler Pan (12 ¾ ” x 1 ¼” x 16 ½ “)
XL** Broiler Pan (17 ” x 1 ¼” x 19 1/4“)
WB48X10055 (US) 222D2097G001 (Canada)
WB48X10056 (US) 222D2097G002 (Canada)
WB48X10057 (US) Not available in Canada
Parts
Oven racks
Oven elements
Light bulbs
Probe
Part numbers vary by model
Part numbers vary by model
Part numbers vary by model
Part numbers vary by model
Cleaning Supplies
CitruShine Stainless Steel Wipes
WX10X10007
CeramaBryte Stainless Steel Appliance Cleaner PM10X311
Graphite Lubricant
WB02T10303
*The large broiler pan does not fit in 20”/24” ranges.
**The XL broiler pan does not fit in 24” wall ovens, 27”drop ins or 20”/24” ranges
How to Remove Protective Shipping Film and Packaging Tape
Carefully grasp a corner of the protective shipping film with your fingers and slowly peel it from the appliance surface.
Do not use any sharp items to remove the film. Remove all of the film before using the appliance for the first time.
To assure no damage is done to the finish of the product, the safest way to remove the adhesive from packaging
tape on new appliances is an application of a household liquid dishwashing detergent. Apply with a soft cloth and
allow to soak.
NOTE: The adhesive must be removed from all parts. It cannot be removed if it is baked on.
7
49-80668-2
Single Wall Oven
11
10
1
Convection
Oven
Broil
Bake
Probe
1
4
7
2
5
8
0
3
6
Hi/Lo/Crisp
Lights
Bake
Roast
9
Multi Rack
Delay
Steam
Clean
9
Time
Traditional
AM/PM
Cancel
Off
Start
Set
Remote
Enable
Lock
Controls
Cook
Time
Timer
On/Off
Broil
Self
Clean
Bake
Proof
Warm
Clock
Hi/Lo
AM/PM
Hold 3 Sec
12 13
5
4
6
7
8
3
2
to turn on. Press the desired cooking mode and
temperature then press Start. A cook time may also
be programmed if desired. This can only be used
with Traditional Bake, Convection Bake, Convection
Bake Multi Rack, Convection Roast and Self-Clean.
1. Convection Cooking Modes: Convection
cooking modes use increased air circulation
to improve performance. The type of benefit
depends on the mode. Your oven has the following
convection cooking modes: Bake, Bake Multi Rack,
Roast, Broil Hi, Broil Lo, and Broil Crisp. See the
Cooking Modes section for more information.
NOTE: When using the delay time feature, foods
that spoil easily—such as milk, eggs, fish, stuffings,
poultry and pork—should not be allowed to sit for
more than 1 hour before or after cooking. Room
temperature promotes the growth of harmful bacteria.
Be sure that the oven light is off because heat from
the bulb will speed harmful bacteria growth.
2. Traditional Cooking Modes: Your oven has
the following traditional cooking modes: Bake, Broil
Hi, Broil Lo, Proof and Warm. See the Cooking
Modes section for more information.
3. Clean: Your oven has two cleaning modes: Self
Clean and Steam Clean. See the Cleaning the
Oven section for important information about
using these modes.
10. Probe: Monitors internal food temperature
and turns the oven off when the food reaches
the programmed temperature. Insert the probe,
program the cooking mode, and program the probe
temperature. See the Cooking Modes section for
more information. The probe can only be used
with Traditional Bake, Convection Bake, and
Convection Roast.
4. Start: Must be pressed to start any cooking,
cleaning, or timed function.
5. Cancel/Off: Cancels ALL oven operations except
the clock and timer.
6. Cook Time: Counts down cooking time and turns
off the oven when the cooking time is complete.
Press the Cook Time pad, use the number pads to
program a cooking time in hours and minutes, then
press Start. This can only be used with Traditional
Bake, Convection Bake, Convection Bake Multi, and
Convection Roast.
11. Oven Light(s): Turns the oven light(s) on or off.
12. Remote Enable (on some models):
Allows the oven to be operated remotely. Once
connectivity is established, pressing the Remote
Enable pad allows the oven to be operated from
a mobile device. Opening the oven door while
the oven is idle, or ending a cook cycle ends this
capability and requires the button to be pressed
7. Clock: Sets the oven clock time. Press the Clock
pad and the number pads to program the clock.
Make sure to select AM or PM. Press Start to save
the time.
again to enable remote operation. Both the
and
the remote enable light in the display must be solid
and lit to allow remote operation. If either the icon
or the remote enable light are not lit or are blinking,
the remote enable feature will not work. Additional
guidance is provided in the included insert and
through the mobile app.
8. Timer: Works as a countdown timer. Press the
Timer pad and the number pads to program the
time in hours and minutes. Press the Start pad.
The oven will continue to operate when the timer
countdown is complete. To turn the timer off press
the Timer pad.
13. Lock Controls: Locks out the control so that
pressing the pads does not activate the controls.
Press and hold the Lock Controls pad for three
seconds to lock or unlock the control. Cancel/Off is
always active, even when the control is locked.
9. Delay Time: Delays when the oven will turn
on. Use this to set a time when you want the oven
to start. Press the Delay Time pad and use the
number pads to program the time of day for the oven
8
49-80668-2
Double Wall Oven
11
10
2
5
1
Convection Upper Oven
Delay
Broil
Upper Oven
Lower Oven
Start
Bake
Probe
1
4
7
2
5
8
0
3
6
Time
Hi/Lo/Crisp
AM/PM
Bake
Roast
Multi Rack
Upper Oven
Upper Oven
Cancel
Oven
Light
Timer
On/Off
Steam
Clean
9
Off
Traditional
Broil
Set
4
Remote
Enable
Lock
Cancel
Off
Cook
Time
Oven
Light
Timer
On/Off
Self
Clean
Bake
Proof
Warm
Clock
Hi/Lo
Controls
AM/PM
Hold 3 Sec
Lower Oven
Lower Oven
13
14
3
6
12
8
9
7
1. Upper Oven and Lower Oven: Designates
which oven to use. Press the Upper Oven or Lower
Oven pad to select an oven, then press the desired
cooking mode pad. The oven control will default to
the upper oven.
10. Delay Time: Delays when the oven will turn
on. Use this to set a time when you want the oven
to start. Press the Delay Time pad and use the
number pads to program the time of day for the oven
to turn on. Press the desired cooking mode and
temperature then press Start. A cook time may also
be programmed if desired. This can only be used with
Traditional Bake, Convection Bake, Convection Bake
Multi Rack, Convection Roast and Self-Clean
2. Convection Cooking Modes: Convection
cooking modes use increased air circulation to
improve performance. The type of benefit depends
on the mode. Your oven has the following convection
cooking modes: Bake, Bake Multi Rack, Roast, Broil
Hi, Broil Lo, and Broil Crisp. See the Cooking Modes
section for more information.
NOTE: When using the delay time feature, foods
that spoil easily—such as milk, eggs, fish, stuffings,
poultry and pork—should not be allowed to sit for
more than 1 hour before or after cooking. Room
temperature promotes the growth of harmful bacteria.
Be sure that the oven light is off because heat from
the bulb will speed harmful bacteria growth.
3. Traditional Cooking Modes: Your oven has
the following traditional cooking modes: Bake, Broil Hi,
Broil Lo, Proof and Warm. See the Cooking Modes
section for more information.
11. Probe: Monitors internal food temperature and
turns the oven off when the food reaches the
programmed temperature. Select upper or lower,
insert the probe, program the cooking mode, and
program the probe temperature. See the Cooking
Modes section for more information. The probe can
only be used with Traditional Bake, Convection
Bake, and Convection Roast.
4. Clean: Your oven has two cleaning modes: Self
Clean and Steam Clean. See the Cleaning the
Oven section for important information about using
these modes.
5. Start: Must be pressed to start any cooking,
cleaning, or timed function.
12. Oven Light(s): Turns the oven light(s) on or off.
6. Cancel/Off: Cancels ALL oven operations except
the clock and timer.
13. Remote Enable (on some models): Allows
the oven to be operated remotely. Once connectivity
is established, pressing the Remote Enable pad
allows the oven to be operated from a mobile device.
Opening the oven door while the oven is idle, or
ending a cook cycle ends this capability and requires
the button to be pressed again to enable remote
7. Cook Time: Counts down cooking time and turns
off the oven when the cooking time is complete.
Press the Cook Time pad, use the number pads to
program a cooking time in hours and minutes, then
press Start. This can only be used with Traditional
Bake, Convection Bake, Convection Bake Multi, and
Convection Roast.
operation. Both the
and the remote enable light
in the display must be solid and lit to allow remote
operation. If either the icon or the remote enable light
are not lit or are blinking, the remote enable feature
will not work. Additional guidance is provided in the
included insert and through the mobile app.
8. Clock: Sets the oven clock time. Press the Clock
pad and the number pads to program the clock. Make
sure to select AM or PM. Press Start to save the time.
9. Timer: Works as a countdown timer. Press the
Timer pad and the number pads to program the time
in hours and minutes. Press the Start pad. The oven
will continue to operate when the timer countdown is
complete. To turn the timer off press the Timer pad.
14. Lock Controls: Locks out the control so that
pressing the pads does not activate the controls.
Press and hold the Lock Controls pad for three
seconds to lock or unlock the control. Cancel/Off is
always active, even when the control is locked.
9
49-80668-2
Special Features
There are numerous special features that are controlled using the number key pad.
•
•
•
•
•
Degree - Fahrenheit or Celsius temperature display
End tone - Cycle End Tone
•
•
•
12hr shutoff - 12 Hour Shutoff
Sabbath - Sabbath mode
Sound - Tone Volume
Temp Offset - Adjust the oven temperature
(Double ovens have upper and lower options)
Setting - Clock Setting
•
•
Notification Light Bar - Turns the light indicator on or off
Default - Reset control to factory settings
Auto Recipe - Auto Recipe Conversion
(for Convection Baking)
To change the Special Features settings follows these
guidelines.
Press and hold the Traditional Bake and Traditional
Broil pads for 3 seconds simultaneously.
1
4
7
2
5
8
0
3
6
1
7
3
When you enter the special features mode:
Enter
0
=
•
The numbers 2 and 8 act as up and down to scroll
9
9
thru the features and their settings.
•
The numbers 4 and 6 act as right and left to change
back and forth from scrolling thru the features to
changing the feature settings.
Set
Set
Cook
Time
Cook
Time
Clock
Clock
AM/PM
AM/PM
•
The number 5 acts as an enter pad.
Press and hold the Traditional Bake and Traditional
Broil pads for 3 seconds simultaneously to exit the
special feature mode.
Example: Adjusting the Oven Temperature
1. Press and hold the Traditional Bake and Traditional 4. Press the number 2 or 8 pads to either increase or
Broil pads for 3 seconds simultaneously to enter
special features mode.
decrease the temperature in one degree Fahrenheit
increments up to + 35º F or down to -35º F.
2. Press the number 2 pad until the display reads “Temp 5. Press the number 5 pad to save your desired change.
Offset” (double wall ovens will have a selection for
both the upper and lower ovens).
6. Press the number 4 pad to return to the other features.
7. Press and hold the Traditional Bake and Traditional
3. Press the number 6 pad to change the special feature
Broil pads for 3 seconds simultaneously to exit the
special feature mode.
setting.
Fahrenheit or Celsius Temperature Display
Auto Recipe Conversion
Your oven control is set to use Fahrenheit temperature
units but can be changed to use Celsius temperature
units if preferred.
When using Convection Bake or Convection Bake
Multi cooking modes, Auto Recipe conversion will
automatically reduce the programmed cooking
temperature. Note that this option does not convert
convection baking times, only temperatures.
Cycle End Tone
This is the tone that signals the end of a timer. You can
change it to be one tone (bEEP) or a continuous repeating
tone (con).
12-hour Shutoff
When this feature is turned on, the oven will automatically
turn off after 12 continuous hours of use.
Tone Volume
This feature allows the oven tone volume to be adjusted
between high, medium (default), low, and off.
Default
This feature resets all of the special features to the
default settings originally on the oven.
Clock Setting
This feature specifies how the time of day will be
displayed. Options are for a standard 12-hour clock with
AM and PM selections, 24-hour military time display, or
for no display.
10
49-80668-2
Special Features (cont.)
the number 6 pad to allow the number 2 or 8 pad to
change the Sabbath feature setting from “oFF” to “on”.
Adjust the Oven Temperature
(Upper and Lower on some models)
Press the number 5 pad to enter the selection. Press
and hold the Traditional Bake and Traditional Broil
pads for 3 seconds to exit special features mode. A ]
will appear in the display and the clock will not display.
This feature allows the oven temperature to be adjusted
up to 35ºF hotter or down to 35ºF cooler. Use this
feature if you believe your oven temperature is too hot
or too cold and wish to change it. For double oven
models the upper and lower ovens are adjusted
separately. This adjustment affects Traditional Bake,
Convection Bake, and Convection Bake Multi Rack
modes.
Note that if you have a double wall oven, when you
place the control into Sabbath mode, both ovens are
now in Sabbath mode and available for cooking.
Once in Sabbath mode, at any time you can press
Bake, the control will start at 350F but you can use the
number pads to enter a different temperature between
170F and 550F if necessary, and then press Start. No
sound will be given when the keys are pressed. At a
random time between 30 seconds and 1 minute, ][, will
appear in the display indicating the oven is running.
Notification Light Bar (on some models)
This feature uses a light bar between the door and
the control panel for easy visual indication of preheat
and cook time status. This feature can be turned on
or off in the special features of your oven. This feature
works with Convection Bake, Convection Bake Multi,
Convection Broil, Convection Roast, Traditional Bake,
Traditional Broil, Warm, Proof, Self Clean, Cook Time
and Timer. On a double wall oven the notification
lighting indicates the status of the upper oven only.
Below is a description of the different light conditions.
Note that both ovens of a double wall oven can be
used in Sabbath mode. Each oven can be programmed
to a different temperature and each oven must be
programmed separately. When programming both
ovens, please wait until one oven is running before
starting the second oven.
OFF - No oven or timer function
is running or the feature has been
turned off in special features.
If you need to adjust the temperature, press Bake, use
the number pads to enter a new temperature between
170F and 550F, and press Start.
PULSING BAR - The oven is pre-
heating. The light bar will pulse until
the oven set temperature has been
reached.
To turn the oven off, press Cancel/Off at any time. The
oven will immediately turn off and the, ][ will change to ]
indicating that the oven has turned off.
Note that each oven of a double wall oven must be
turned off separately.
PROGRESS BAR - Will slowly
progress to a fully lit bar as the
timer counts down.
To exit Sabbath mode, first turn the oven off. Then
press and hold the Traditional Bake and Traditional
Broil pads for 3 seconds to enter special features
mode. You will not be able to enter special features
mode if the oven is not turned off.
NOTE: If the Cook Time button is used, the light bar
and the oven will turn off when the time reaches zero. If
Timer button is used the light bar will remain solid when
time reaches zero.
Use the number 2 or 8 pad to scroll thru the special
features options to "SAbbAth" and then press the 6 pad
to allow the number 2 or 8 pad to change the Sabbath
feature setting from “on” to “oFF”.
SOLID BAR - The oven is at the
set temperature and/or function or
your kitchen timer is complete.
Press the number 5 pad to enter the selection. Then
press and hold the Traditional Bake and Traditional
Broil pads for 3 seconds to exit special features mode.
NOTE: The progress bar for timed functions takes
priority over the solid or pulsating functions if both are
being used at the same time.
NOTE: If power outage occurs during Sabbath mode
the unit will remain in Sabbath mode but off when
power is restored.
Sabbath
Sabbath mode disables the oven lights, (the oven
light will not turn on when the door is opened and
the notification light bar will be disabled), all sounds
(the control will not beep when a button is pressed),
Convection modes, Broil modes, Warm, Proof, Cook
Time, Timer, Clock, and Delay Time functions. Sabbath
mode can only be used with Bake. This feature
conforms to the Star-K Jewish Sabbath requirements.
If you wish to use the Cook Time feature to bake in the
oven and then have the oven automatically turn off, do
not enter Sabbath mode. You will need to change the
End Tone from a continuous beep to a single beep, turn
the Tone Volume off, and turn the oven light on using
the control panel or remove the light bulb and then you
can program the oven for the desired cook time in bake.
Press and hold the Traditional Bake and Traditional
Broil pads for 3 seconds to enter special features
mode. Use the number 2 or 8 pad to scroll thru the
special features options to “SAbbAtH” and then press
11
49-80668-2
Oven Racks
Your oven has six rack positions. Recommended rack
positions for various types of foods are provided in the
Cooking Guide. Adjusting rack position is one way to
impact cooking results. For example, if you would prefer
darker tops on cakes, muffins, or cookies, try moving
food one rack position higher. If you find foods are too
brown on top try moving them down next time.
The oven
has 6 rack
positions
When baking with multiple pans and on multiple racks,
ensure there is at least 1½" between pans to allow
sufficient space for air to flow.
Oven Racks
Your oven may have extension racks and/or traditional
flat racks.
Upper Front Rail
Lower Front Rail
To avoid possible burns, place the racks in the desired
position before you turn the oven on.
Extension Racks
Extension racks have a frame that locks into the rack
supports on both sides. Once the frame is locked into
place, always pull the rack out, by its upper front rail, to
its full extension stop position, when placing or removing
cookware.
Lift to unlock
front rack
locks from the
rack support
Lower
front rail
If extension racks are difficult to extend, lubricate the
racks with the graphite lubricant provided with your
oven. Remove the rack from the oven, remove debris in
the slide tracks with a paper towel, shake the graphite
lubricant and place 4 small drops on the two bottom
tracks of the left and right sides. Open and close the rack
several times to distribute the lubricant.
Upper
front rail
Front
rack
lock
To order additional graphite lubricant, read the
Assistance and Accessories section at the beginning of
this manual.
Lower
front rail
Upper
front rail
To Remove An Extension Rack:
1. Make sure the rack is pushed all the way into the oven.
2. Grasp the rack by both its upper front rail and its lower
front rail and lift straight up to unlock the front rack
locks from the rack supports.
3. Firmly holding onto both the upper and lower front rails,
pull the rack forward and remove it from the oven.
Rear rack lock
Rack support
To Replace An Extension Rack:
1. Place the rear rack locks over and onto the rack
supports.
2. Slide the rack all the way in until the rear rack locks
are secure on the rear rack supports and press the
front rack locks onto the front rack supports.
If extension racks are difficult to replace or remove, wipe
the oven rack supports with cooking oil. Do not wipe oil
on the rack slides.
Slide the rack all the way
in and push down to lock
the front locks onto the
front rack supports
Front rack lock
12
49-80668-2
Oven Racks (cont.)
Traditional Flat Racks
The racks have stops so that when placed correctly on
the supports they will stop before coming completely out
and will not tilt. When placing and removing cookware,
Flat Rack
pull the rack out until it stops.
To Remove a Rack
Pull it toward you, tilt the front end up and pull it out.
Stop-lock
To Replace a Rack
Tilt the front of the rack up, hook the rear locating posts
under the rack supports, push the rack back (past the
stop-locks) and lower it into position. Push the rack all
the way in.
Post
Rack Support
If flat racks are difficult to slide and/or remove, place
some cooking oil on a soft cloth or paper towel and rub
onto the sides of the rack and each rack support.
CAUTION:
CAUTION:
Use caution when removing a rack from lowest position as door may be hot.
Never place cooking utensils, aluminum foil, pizza or baking stones, or any other
items on the oven floor. There is a heating element beneath the oven floor. Placing items on the oven floor
may cause the oven to overheat, resulting in damage to the oven and risk of damage or fire to cabinets.
Aluminum Foil
Do not use aluminum foil to line oven bottoms. The foil will trap heat below and upset the performance of the
oven. Foil can melt and permanently damage the oven bottom. Damage from improper use of aluminum foil is not
covered by the product warranty.
Foil may be used to catch spills by placing a sheet on a lower rack, several inches below the food. Do not use
more foil than necessary and never entirely cover an oven rack with aluminum foil. Keep foil at least 1-1/2” from
oven walls to prevent poor heat circulation.
13
49-80668-2
Cooking Modes
Your new oven has a variety of cooking modes to help you get the best results. These modes are described
below. Refer to the Cooking Guide section for recommendations for specific foods. Remember, your new oven
may perform differently than the oven it is replacing.
Baking and Roasting Modes
Broiling Modes
Always broil with the door closed. The broil element in
this oven is very powerful. Monitor food closely while
broiling. Use caution when broiling on upper rack
positions as placing food closer to the broil element
increases smoking, spattering, and the possibility
of fats igniting. Broiling on rack position 6 is not
recommended.
Select a mode for baking and roasting based on the
type and quantity of food you are preparing. When
preparing baked goods such as cakes, cookies, and
pastries always preheat the oven first. Follow recipe
recommendations for food placement. If no guidelines
are provided, center food in the oven.
Try broiling foods that you would normally grill. Adjust
rack positions to adjust the intensity of the heat to the
food. Place foods closer to the broil element when a
seared surface and rare interior is desired. Thicker foods
and foods that need to be cooked through should be
broiled on a rack position farther from the broiler or by
using Traditional Broil Lo or Convection Broil Lo. For best
performance, center food below the broil heating element.
Traditional Bake
The traditional bake mode is intended for single rack
cooking. This mode uses heat primarily from the lower
element but also from the upper element to cook food.
To use this mode press the Bake pad under Traditional,
enter a temperature, and then press Start. Preheating is
generally recommended when using this mode.
Convection Bake with Direct Air
Traditional Broil Hi
The Convection Bake mode is intended for single rack
cooking. This mode uses heat from the lower element
and also the upper and rear elements, along with air
movement directly down from the top of the oven to
enhance evenness. Your oven is equipped with Auto
Recipe Conversion, so it is not necessary to convert
the temperature when using this mode. To use this
mode press the Bake pad under Convection, enter
a temperature, and then press Start. Preheating is
generally recommended when using this mode.
The Traditional Broil Hi mode uses intense heat from the
upper element to sear foods. Use Broil Hi for thinner cuts
of meat and/or foods you prefer less done on the interior.
To use this mode press the Broil pad once under
Traditional and then press Start. It is not necessary to
preheat when using this mode.
Traditional Broil Lo
The Traditional Broil Lo mode uses less intense heat
from the upper element to cook food thoroughly while
also producing surface browning. Use Broil Lo for thicker
cuts of meat and/or foods that you would like cooked all
the way through. To use this mode press the Broil pad
twice under Traditional and then press Start. It is not
necessary to preheat when using this mode.
Convection Bake Multi Rack
The Convection Bake Multi Rack mode is intended
for baking on multiple racks at the same time. This
mode uses heat primarily from the rear element but
also heat from the upper and lower elements, along
with air movement from the convection fan to enhance
cooking evenness. Your oven is equipped with Auto
Recipe Conversion, so it is not necessary to convert the
temperature when using this mode. Baking time might
be slightly longer for multiple racks than what would
be expected for a single rack. To use this mode press
the Bake Multi Rack pad under Convection, enter a
temperature, and then press Start. Always preheat when
using this mode.
Convection Broil Hi with Direct Air
The Convection Broil Hi mode uses intense heat from
the upper element along with air movement directly
down from the top of the oven for improved searing and
browning. To use this mode press the Broil pad once
under Convection and then press Start. For best results
preheat 5 minutes when using this mode.
Convection Broil Lo with Direct Air
The Convection Broil Lo mode uses less intense heat from
the upper element along with air movement directly down
from the top of the oven. To use this mode press the Broil
pad twice under Convection and then press Start. For
best results preheat 5 minutes when using this mode.
Convection Roast with Direct Air
The Convection Roast mode is intended for roasting
whole cuts of meat on a single rack. This mode uses
heat from the lower, upper, and rear elements along with
air movement directly down from the top of the oven
to improve browning and reduce cooking time. It is not
Convection Broil Crisp with Direct Air
necessary to convert temperature. Check food earlier than The Convection Broil Crisp mode is intended as a
the recipe suggested time when using this mode, or use
the probe. To use this mode press the Roast pad under
finishing mode at the end of a cooking cycle to add
surface browning to a dish such as a casserole or a
Convection, enter a temperature, and then press Start. It roast. To use this mode press the Broil pad three times
is not necessary to preheat when using this mode.
under Convection and then press Start. Monitor food
closely to prevent over browning.
14
49-80668-2
Cooking Modes (Cont.)
3. Program the desired probe and cooking mode settings
by pressing the Probe pad and entering the desired
food temperature, then pressing the cook mode pad
(Traditional Bake, Convection Bake, or Convection
Roast) and entering the desired cooking temperature.
Proof
Proof mode is designed for rising (fermenting and
proofing) bread doughs. Press the Proof pad and then
press Start. Cover dough well to prevent drying out.
Bread will rise more rapidly than at room temperature.
Proper Probe Placement Guidelines
After preparing the meat and placing it on the cooking
pan follow these guidelines for proper probe placement.
Ŷꢀ Insert the probe completely into the meat, up to the
handle, such that the point of the probe will rest in the
center of the thickest part of the meat.
Ŷꢀ The probe should not touch bone, fat or gristle.
Ŷꢀ For whole poultry insert the probe into the thickest
part of the breast.
Warm
Warm mode is designed to keep hot foods hot for up to 3
hours. To use this mode, press the Warm pad then press
Start. Cover foods that need to remain moist and do not
cover foods that should be crisp. Preheating is not required.
Do not use warm to heat cold food other than crisping
crackers, chips or dry cereal. It is also recommended that
food not be kept warm for more than 2 hours.
Probe
Ŷꢀ For boneless roasts, insert the probe into the center
of the roast.
Internal food temperature is frequently used as an
indicator of doneness, especially for roasts and poultry.
The Probe mode monitors the internal food temperature
and turns the oven off when the internal food
temperature reaches the programmed temperature.
Minimum temperatures for food safety can be found at
be used with Traditional Bake, Convection Bake, and
Convection Roast modes.
Ŷꢀ For bone-in ham or lamb, insert the probe into the
center of the lowest large muscle or joint.
Ŷꢀ For casseroles or dishes such as meatloaf, insert the
probe into the center of the dish.
Ŷꢀ For fish, insert the probe from just above the gill into
the meatiest area, parallel to the backbone.
Check the temperature at other locations in the food
with a food thermometer once the probe temperature
is reached to ensure that all portions of the food have
reached desired temperatures.
To use the probe with preheating:
1. Press the desired cook mode (Traditional Bake,
Convection Bake, or Convection Roast) pad and
enter the desired cooking temperature.
2. Insert the probe into the food (see Proper Probe
Placement Guidelines in this section).
3. Once the oven is preheated, place the food in the
oven and connect the probe to the probe outlet,
making sure it is fully inserted. Use caution, the oven
walls and probe outlet are hot.
4. Program the probe temperature by pressing the
Probe pad and entering the desired food temperature.
The maximum internal food temperature that you can
set is 200º F.
Probe Care Guidelines
Note: some double oven models have a probe in the
upper oven only.
Ŷꢀ Use of probes other than the one provided with this
product may result in damage to the probe.
Ŷꢀ Use the handles of the probe and plug when inserting
and removing them from the meat and outlet
Ŷꢀ To avoid damaging your probe, do not use tongs to
pull on the cable when removing it.
Ŷꢀ To avoid breaking the probe, make sure food is
completely defrosted before inserting the probe.
Ŷꢀ To prevent possible burns, do not unplug the probe
from the outlet until the oven has cooled.
Ŷꢀ Never leave the probe inside the oven during a self or
steam clean cycle.
To use the probe without preheating:
1. Insert the probe into the food (see Proper Probe
Placement Guidelines in this section).
2. Place the food in the oven and connect the probe into
the probe outlet in the oven.
Ŷꢀ Do not store the probe in the oven.
Cookware
Cookware Guidelines
Shiny pans can produce more evenly cooked baked
goods such as cakes and cookies.
The material, finish, and size of cookware affect baking
Glass and ceramic pans heat slowly but retain heat well.
These types of pans work well for dishes such as pies
and custards.
Air insulated pans heat slowly and can reduce bottom
browning.
performance.
Dark, coated and dull pans absorb heat more readily
than light, shiny pans. Pans that absorb heat more
readily can result in a browner, crisper, and thicker crust.
If using dark and coated cookware check food earlier
than minimum cook time. If undesirable results are
obtained with this type of cookware consider reducing
oven temperature by 25º F next time.
Keep cookware clean to promote even heating.
15
49-80668-2
Cooking Guide
RECOMMENDED
MODE(S)
RECOMMENDED
RACK POSITION(S)
FOOD TYPE
ADDITIONAL SUGGESTIONS
Baked Goods
Layer cakes, sheet cakes, bundt
cakes, muffins, quick breads on
a Single Rack
Convection Bake
Traditional Bake
3
Use shiny cookware.
Extension rack in higher position if used.
Ensure adequate airflow
Layer cakes* on Multiple Racks
Chiffon cakes (angel food)
Traditional Bake
2 and 4
(see illustration below).
Convection Bake
Traditional Bake
1
3
Use shiny cookware.
Use shiny cookware.
Cookies, biscuits, scones on a
Single Rack
Convection Bake
Cookies, biscuits, scones on
Multiple Racks
Convection Bake
Multi Rack
2 and 4
2, 3 and 5
Extension rack position 4 for 2 racks, and
position 3 for 3 racks. Ensure adequate airflow.
Beef & Pork
Use extension rack; move food down for more doneness/
less searing. Watch food closely when broiling. For best
performance, center food below the broil heating element.
Hamburgers
Traditional Broil Hi
5
Use a broil pan; Preheat 5 minutes if using Convection
Broil Mode. Move food down for more doneness/less
searing. Watch food closely when broiling. For best
performance, center food below the broil heating element.
Convection Broil Hi
Traditional Broil Hi
Steaks & Chops
5
Use a low sided pan such as a broil pan. Preheating is not
necessary. Use probe feature.
Roasts
Poultry
Convection Roast
2 or 3
Use a low sided pan such
as a broil pan. Use probe feature.
Whole chicken
Convection Roast
Broil Hi
2 or 3
1
If breaded or coated in sauce avoid Broil Hi modes. Broil
skin side down first. Watch food closely when broiling. For
best performance when broiling, center food below the
broil heating element.
Bone-in chicken breasts, legs,
thighs
Broil Lo
Convection Bake
Traditional Bake
3
3
Preheat 5 minutes if using Convection Broil. Move food
down for more doneness/less searing and up for greater
searing/browning when broiling. For best performance
when broiling, center food below the broil heating element.
Convection Broil Lo
Convection Bake
Traditional Bake
Boneless chicken breasts
Use a low sided pan such as a broil pan.
Use the probe feature.
Whole turkey
Turkey Breast
Convection Roast
Convection Roast
1 or 2
2 or 3
Use a low sided pan such as a broil pan.
Use the probe feature.
Preheat 5 minutes when Convection Broiling. Watch food
closely when broiling. For best performance, center food
below the broil heating element.
Convection Broil Lo
Broil Lo
5 (1/2 thick or less)
4 (>1/2 inch)
Fish
Use Convection Broil Crisp mode during
last 2-5 minutes of baking to
melt/brown cheese or crisp surface.
Convection Bake
Traditional Bake
Casseroles
3
Frozen Convenience Foods
Pizza, french fries, tator tots,
chicken nuggets, appetizers on
a Single Rack
Convection Bake
Traditional Bake
Use Convection Broil Crisp mode during last
2-5 minutes of cooking to crisp the exterior.
3
Pizza, french fries, tator tots,
chicken nuggets, appetizers on
Multiple Racks
If using Crisp mode, place both pans on top
rack if space allows, otherwise Crisp one
at a time on top rack position.
Convection Bake
Multi Rack
2 and 4
*When baking four cake layers at a time, use racks 2
and 4. Place the pans as shown so that one pan is not
directly above another.
Cook food thoroughly to help protect against food
borne illness. Minimum safe food temperature
recommendations for food safety can be found at
www.IsItDoneYet.gov. Make sure to use a food
thermometer to take food temperatures.
16
49-80668-2
Cleaning The Oven
Be sure electrical power is off and all surfaces are cool before cleaning any part of the oven.
Control Panel
It’s a good idea to wipe the control panel after each use.
Clean with mild soap and water or vinegar and water,
rinse with clean water and polish dry with a soft cloth.
Do not use abrasive cleansers, strong liquid cleansers,
plastic scouring pads or oven cleaners on the control
panel—they will damage the finish.
Oven Exterior
Do not use oven cleaners, abrasive cleansers, strong
liquid cleansers, steel wool, plastic scouring pads, or
cleaning powders on the interior or exterior of the oven.
Clean with a mild soap and water or vinegar and water
solution. Rinse with clean water and dry with a soft cloth.
When cleaning surfaces, make sure that they are at
room temperature and not in direct sunlight.
If stain on the door vent trim is persistent, use a mild
abrasive cleaner and a sponge-scrubber for best results.
Spillage of marinades, fruit juices, tomato sauces and
basting liquids containing acids may cause discoloration
and should be wiped up immediately. Let hot surfaces
cool, then clean and rinse.
Stainless Steel Surfaces (on some models)
Do not use a steel wool pad; it will scratch the surface.
To inquire about purchasing cleaning products including
stainless steel appliance cleaner or polish, read the
Assistance and Accessories sections at the beginning of
this manual.
To clean the stainless steel surface, use warm sudsy
water or a stainless steel cleaner or polish. Always wipe
the surface in the direction of the grain. Follow the cleaner
instructions for cleaning the stainless steel surface.
Oven Interior
The interior of your new oven can be cleaned manually
or by using the Steam Clean or Self Clean modes.
end of the steam clean cycle the door will unlock. Wipe
out any excess water and any remaining soil.
Spillage of marinades, fruit juices, tomato sauces and
basting liquids containing acids may cause discoloration
and should be wiped up immediately. Let hot surfaces
cool, then clean and rinse.
Self Clean Mode
Read Self-Cleaning Oven Safety Instructions at the
beginning of this manual before using Self Clean Mode.
Self clean uses very high temperatures to clean the oven
interior. The oven door will lock when using this feature.
Before operating the self clean cycle, wipe up grease
and soils from the oven. Remove all items from the oven
other than enameled (dark color) racks. Shiny or silver
racks, the meat probe, and any cookware or other items
should all be removed from the oven before initiating a
self clean cycle. Close the door. Press the Self Clean
pad and a default self-clean time is displayed. The clean
time can be changed to any time between 3:00 and
5:00 hours by using the number pads to enter a different
time and pressing Start. For heavily soiled ovens, the
maximum 5 hour clean time is recommended. If you wish
to use the default time, press the Start pad immediately
after pressing the Self Clean pad. The oven will turn off
automatically when the self clean cycle is complete. The
door will stay locked until the oven has cooled down. After
the oven has cooled down wipe any ash out of the oven.
Manual Cleaning
Do not use oven cleaners, abrasive cleaners, strong
liquid cleansers, steel wool, scouring pads, or cleaning
powders on the interior of the oven. Clean with a mild
soap and water or vinegar and water solution. Rinse with
clean water and dry with a soft cloth. When cleaning
surfaces, make sure that they are at room temperature.
Steam Clean Mode
Steam clean is intended to clean small spills using water
and a lower cleaning temperature than Self-Clean.
To use the Steam Clean feature, wipe grease and soils
from the oven. Pour one cup of water into the bottom of
the oven. Close the door. Press the Steam Clean pad
and then press Start. The oven door will lock. You can
not open the door during the 30 minute steam clean as
this will decrease the steam clean performance. At the
17
49-80668-2
Oven Racks
The racks that were provided with your oven (dark
enameled racks, not shiny) may remain in the oven
during the self-cleaning cycle without being damaged.
To manually clean racks, use warm, soapy water. Make
sure not to wash the rack slides on an extension rack.
If racks become more difficult to remove from the oven,
put some vegetable oil on a soft cloth or paper towel
and rub onto the oven rack supports. Do not wipe the
oil on an extension rack slide.
Periodically, after several self-clean cycles, the
extension rack slides may need to be lubricated using
the graphite lubricant shipped with your wall oven. To
order additional graphite lubricant read the Assistance
and Accessories sections at the beginning of this
manual.
1. Remove extension rack from the oven. See the
Extension Oven Racks section.
2. Fully extend the rack on a table or countertop.
Newspaper may be placed underneath the rack for
easy clean up.
3. If there is debris in the slide tracks, wipe it away
using a paper towel. NOTE: Any graphite lubricant
wiped away must be replaced.
4. Shake the graphite lubricant before opening it.
Starting with left slide mechanism of the rack,
place four (4) small drops of lubricant on the two
(2) bottom tracks of the slide close to the bearing
carriers.
5. Repeat for the right slide mechanism of the rack.
6. Open and close the rack several times to distribute
the lubricant.
7. Replace the cap on the lubricant and shake it again.
Turn the rack over and repeat steps 3, 4, 5 and 6.
8. Close the rack, turn rack right-side-up and place in
the oven. See the Extension Oven Racks section.
9. Repeat above steps for each rack.
NOTE: Do not spray with cooking spray or other
lubricant sprays.
Probe
The temperature probe may be cleaned with soap and
water or a soap-filled scouring pad. Cool the temperature
probe before cleaning. Scour stubborn spots with a soap-
filled scouring pad, rinse and dry.
To order additional temperature probes read the
Assistance and Accessories sections at the beginning of
this manual.
Ŷ Do not immerse the temperature probe in water.
Ŷ Do not store the temperature probe in the oven.
Ŷ Do not leave the temperature probe inside the oven
during a self or steam clean cycle.
18
49-80668-2
Maintenance
Oven Light Replacement
SHOCK OR BURN HAZARD: Before replacing oven light bulb, disconnect the electrical
power to the oven at the main fuse or circuit breaker panel. Failure to do so may result in
electric shock or burn.
WARNING
BURN HAZARD: The glass cover and bulb should be removed when cool. Touching hot
glass with bare hands or a damp cloth can cause burns.
CAUTION
1. Disconnect power at the main fuse or circuit breaker
panel.
2. Remove oven racks.
3. Slide a flat blade screwdriver between the housing
and the glass light cover.
4. Support the glass light cover with two fingers to
prevent the cover from falling to the bottom of the
oven. Be careful not to chip the oven coating.
8. Do not touch the glass of the new replacement bulb
with your fingers. It will cause the bulb to fail when it
lights. Grasp the replacement bulb with a clean towel
or facial tissue with the prongs facing down. Align the
two prongs in the ceramic holder, pressing gently until
the bulb is securely in the ceramic socket.
9. Slide the protective lens into the holder and push until
the clips snap into the housing.
10.Reconnect power.
5. Gently twist the screwdriver blade to loosen the glass
light cover.
6. Remove the glass light cover.
7. Remove the bulb by firmly grasping and sliding the
bulb straight out until the two prongs have cleared the
ceramic holder.
Lift-Off Oven Door
The door is very heavy. Be careful when removing and lifting the door.
Do not lift the door by the handle.
To remove the door:
1. Fully open the door.
Slot
2. Pull the hinge locks down toward the door frame, to
the unlocked position. A tool, such as a small flat-
blade screwdriver, may be required.
3. Firmly grasp both sides of the door at the top.
4. Close door to the door removal position. The door
should be open approximately 3" with no obstruction
above the door.
Hinge lock
5. Lift door up and out until both hinge arms are clear of
the slots.
Removal position
Pull hinge locks down to unlock
To replace the door:
1. Firmly grasp both sides of the door at the top.
2. Starting on the left side, with the door at the same
angle as the removal position, seat the indentation of
the hinge arm into the bottom edge of the hinge slot.
The notch in the hinge arm must be fully seated into
the bottom of the slot. Repeat for right side.
Bottom
edge of
slot
Hinge arm
Hinge
arm
3. Fully open the door. If the door will not fully open, the
indentation is not seated correctly in the bottom edge
of the slot.
Hinge
lock
Indentation
4. Push the hinge locks up against the front frame of the
oven cavity, to the locked position.
Push hinge locks up to lock
5. Close the oven door.
19
49-80668-2
Notes
20
49-80668-2
Notes
21
49-80668-2
Troubleshooting tips ... Before you call for service
Save time and money! Review the charts on the following pages first and you may not need to call for service.
Problem
Possible Cause
What To Do
My new oven doesn't
cook like my old one.
Is something wrong
with the temperature
settings?
Your new oven has a different cooking
system from your old oven and therefore
may cook differently than your old oven.
For the first few uses, follow your recipe
times and temperatures carefully. If you still
think your new oven is too hot or too cold,
you can adjust the temperature yourself
to meet your specific cooking preference.
NOTE: This adjustment affects traditional
bake Traditional Bake, Convection Bake and
Convection Bake Multi temperatures; it will
not affect Convection Roast, Traditional Broil,
Convection Broil or Clean.
Food does not bake
properly
Oven controls improperly set.
See the Cooking Modes section.
Rack position is incorrect or rack is not
level.
See the Cooking Modes section and Cooking
Guide.
Incorrect cookware or cookware of improper See the Cookware section.
size being used.
Oven temperature needs adjustment.
Ingredient substitution
See the Special Features section.
Substituting ingredients can change the
recipe outcome.
Food does not broil
properly
Oven controls improperly set.
Make sure you select the appropriate broil
mode. NOTE: Convection crisp is not for
broiling foods.
Improper rack position being used.
See the Cooking Guide for rack location
suggestions.
Food being cooked in a hot pan.
Cookware not suited for broiling.
Make sure cookware is cool
Use a pan specifically designed for broiling
If using aluminum foil conform to pan slits.
Aluminum foil used on the broiling pan and
grid has not been fitted properly and
slit as recommended.
In some areas the power (voltage) may be
low.
Preheat the broil element for 10 minutes.
See the Special Features section.
Oven temperature too
hot or too cold
Oven temperature needs adjustment.
Oven not work or
appears not to work
A fuse in your home may be blown or the
circuit breaker tripped.
Replace the fuse or reset the circuit breaker.
See the Using the Oven section.
Oven controls improperly set.
Oven is in Sabbath Mode
Verify, that the oven is not in Sabbath Mode.
See the Special Features section.
“Crackling” or
“popping” sound
This is the sound of the metal heating
and cooling during both the cooking and
cleaning functions.
This is normal.
Why is my range
making a "clicking"
noise when using my
oven?
Your range has been designed to maintain
a tighter control over your oven's
This is normal.
temperature. You may hear your oven's
heating elements "click" on and off more
frequently than in older ovens to achieve
better results during baking, broiling,
convection, and self-clean cycles.
Clock and timer do not A fuse in your home may be blown or the
work circuit breaker tripped.
Replace the fuse or reset the circuit breaker.
22
49-80668-2
Troubleshooting tips ... Before you call for service
Problem
Possible Cause
What To Do
Oven light does not
work
Light bulb is loose or defective.
Tighten or replace bulb.
Pad operating light is broken.
Call for service.
Oven will not self-
clean
The temperature is too high to set a
self-clean operation.
Allow the oven to cool and reset the controls.
Oven controls improperly set.
Excessive soil or grease.
See the Cleaning the Oven section.
Excessive smoking
during clean cycle
Press the Cancel/Off pad. Open the windows to rid
the room of smoke. Wait until the LOCKED light goes
off. Wipe up the excess soil and reset the clean cycle.
Excessive smoking
during broiling
Food too close to burner element.
Oven too hot.
Lower the rack position of the food.
Oven door will not
open after a clean
cycle
Allow the oven to cool below locking temperature.
Oven not clean after
a clean cycle
Oven controls improperly set.
Oven was heavily soiled.
See the Cleaning the Oven section.
Clean up heavy spillovers before starting the clean
cycle. Heavily soiled ovens may need to self-clean
again or for a longer period of time.
"LOCK DOOR"
flashes in the
display
The self-clean cycle has been selected
but the door is not closed.
Close the oven door.
LOCKED light is on
when you want to
cook
The oven door is locked because
the temperature inside the oven
has not dropped below the locking
temperature.
Press the Cancel/Off pad. Allow the oven to cool.
“F— and a number
or letter” flash in
the display
You have a function error code.
Press the Cancel/Off pad. Allow the oven to cool for one
hour. Put the oven back into operation.
If the function code repeats.
Disconnect all power to the oven for at least 30
seconds and then reconnect power. If the function
error code repeats, call for service.
Display goes blank
A fuse in your home may be blown or the Replace the fuse or reset the circuit breaker.
circuit breaker tripped.
The clock is turned off.
Oven is in Sabbath Mode.
See the Special Features section.
Verify that the oven is not in Sabbath Mode.
See the Special Features section.
Power outage,
clock flashes
Power outage or surge
Reset the clock. If the oven was in use, you must
reset it by pressing the Cancel/Off pad, setting the
clock and resetting any cooking function.
“Burning” or “oily”
odor emitting from
the vent
This is normal in a new oven and will
disappear in time.
To speed the process, set a self-clean cycle for a
minimum of 3 hours. See the Cleaning the Oven
section.
Strong odor
An odor from the insulation around
the inside of the oven is normal for the
first few times the oven is used.
This is temporary and will go away after several uses
or a self-clean cycle.
Fan noise
A cooling fan may automatically turn
on.
This is normal. The cooling fan will turn on to cool
internal parts. It may run for up to 1-1/2 hours after the
oven is turned off.
My oven door glass No. The inner oven glass is coated with This is normal. Under certain light or angles, you may
appears to be
a heat barrier to reflect the heat back
into the oven to prevent heat loss and
keep the outer door cool while baking.
see this tint or rainbow color.
"tinted" or have a
"rainbow" color. Is
this defective?
23
49-80668-2
Troubleshooting tips ... Before you call for service
Problem
Possible Cause
What To Do
Sometimes the
Cookware or food in oven
The cookware or food in the oven will cause the oven
to take longer to preheat. Remove items to reduce
preheat time.
oven takes longer to
preheat to the same
temperature
Number of racks in oven
Different cooking modes
Adding more racks to the oven will cause the oven to
take longer to preheat. Remove some racks.
The different cooking modes use different preheat
methods to heat the oven for the specific cooking
mode. Some modes will take longer than others (i.e.
convection bake multi).
Oven will not work
remotely
Router issues, no wireless signal, etc.
Oven is not connected.
For assistance with oven wireless network
connectivity, please call 1-800-220-6899.
24
49-80668-2
|